English PADDLE SWITCH GRINDER DCG416 Congratulations! EC‑Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data...
English h ) Do not let familiarity gained from frequent use of contacts eyes, additionally seek medical help. Liquid tools allow you to become complacent and ignore ejected from the battery may cause irritation or burns. tool safety principles. A careless action can cause severe e ) Do not use a battery pack or tool that is damaged or injury within a fraction of a second.
English FURTHER SAFETY INSTRUCTIONS FOR ALL g ) Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheel for OPERATIONS chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. Causes and Operator Prevention If power tool or accessory is dropped, inspect for of Kickback...
English Safety Warnings Specific for Sanding amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel Operations fragments and accidental contact with wheel and sparks a ) Do not use excessively oversized sanding disc that could ignite clothing.
English WARNING: No connection is to be made to the • Do not place any object on top of charger or place earth terminal. the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Follow the fitting instructions supplied with good quality plugs.
English Battery Packs has reached an appropriate temperature, the yellow light will turn off and the charger will resume the charging procedure. Important Safety Instructions for All The compatible charger(s) will not charge a faulty battery pack. Battery Packs The charger will indicate faulty battery by refusing to light. When ordering replacement battery packs, be sure to include nOTE: This could also mean a problem with a charger.
English Transport Mode: When the cap is attached to the FLEXVOLT CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping battery, the battery is in Transport mode. Keep the cap or falling hazard.
3 x 36 Wh (3 batteries of 36 Wh). Side handle Battery Type Backing flange The following tools operate on a 18 volt battery pack: DCG416 Locking flange These battery packs may be used: DCB181, DCB182, DCB183, Guard DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185, Guard release lever DCB187, DCB189, DCB546, DCB547, DCB548.
Page 15
English off. The switch will need to be released then depressed to subject to variation based on product components, temperature restart tool. and end‑user application. Power‑OFF™ Overload Protection Attaching Side Handle (Fig. C) The power supply to the motor will be reduced in case of WARNING: Before using the tool, check that the handle is motor overload.
Page 16
English Mounting Sanding Backing Pads (Fig. G) The engaging face is slanted and will ride over to the next alignment hole when guard is rotated in a clockwise nOTE: Use of a guard with sanding discs that use backing pads, direction (spindle facing user) but self‑locks in the often called fiber resin discs, is not required.
English 3. Depress spindle lock button 3 and use a wrench on the 1. To turn the tool on, push the lock‑off lever 2 toward the hub of the wire wheel or brush to tighten the wheel. back of the tool, then depress the paddle switch 1 ...
English CAUTION: Use extra care when working over an edge, as is being used. In all edge grinding/cutting operations, the a sudden sharp movement of grinder may be experienced. open side of the guard must be positioned away from the operator. Precautions To Take When Working on a Painted NOTICE: Edge grinding/cutting with a Type 27 wheel Workpiece must be limited to shallow cutting and notching—less...
English The machine must always work in an upgrinding motion. Never let any liquid get inside the tool; never immerse any Otherwise, the danger exists of it being pushed uncontrolled part of the tool into a liquid. out of the cut. Optional Accessories When cutting profiles and square bar, it is best to start at the WARNING: Since accessories, other than those offered smallest cross section.
English Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Locking flange Wire wheels with threaded nut Type 27 guard Wire wheel Wire cup with threaded nut...
Page 21
English Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Type 27 Guard Locking flange...
Page 24
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)