U-Line Echelon CO2075FF Installation Manual
Ice maker/refrigerator
Hide thumbs
Also See for Echelon CO2075FF:
- Service and parts manual (118 pages) ,
- Supplementary manual (6 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for U-Line Echelon CO2075FF
Summary of Contents for U-Line Echelon CO2075FF
-
Page 1: Installation Guide
™ Installation Guide CO2075FF — Ice Maker/Refrigerator www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.com ©2005 U-Line Corporation 02/2005... -
Page 2: Table Of Contents
CO2075FF — Ice Maker/Refrigerator Contents Exterior Cleaning ......Cut-Out Dimensions ...... -
Page 3: Inspect And Plan
CO2075FF — Ice Maker/Refrigerator 2 Inspect and Plan You have received a carton containing your CO2075FF Ice Maker/Refrigerator with a package inside containing a User Manual, a Product Registration Card and water connection parts. Complete and mail the Product Registration Card or register online at www.U-LineService.com. -
Page 4: Exterior Cleaning
3 Prepare Site Your U-Line product has been designed for either free- standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water, drain and electrical connections in the rear. -
Page 5: Product Dimensions
Figure 3 02/2005 CO2075FF — Ice Maker/Refrigerator Reversing the Door (Black and White Units Only) All U-Line units (except Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side. -
Page 6: Other Site Requirements
CO2075FF — Ice Maker/Refrigerator 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 8). Hinge Screw Door Closer Inserts Figure 7 Figure 8 5. Remove existing bottom hinge (3 screws) and remount on opposite side TOP. -
Page 7: Side-By-Side Installation Instructions
Side-By-Side Installation Instructions For a complete refreshment center, install your CO2075FF Ice Maker/Refrigerator beside a U-Line Drawer or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different. • Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit’s Installation Guide. -
Page 8: Full Overlay Door Panel
A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit (P/N U-OL2075B — Black or P/N U-OL2075W — White). Appropriate hardware, Modified Handle, Replacement Hinges and a copy of these instructions will be included in the kit. - Page 9 CAUTION Be careful not to drill too deep! Drilling holes too deep may destroy your door panel. 02/2005 CO2075FF — Ice Maker/Refrigerator 4. Drill hole for upper door hinge (top of panel) (see Figure 16, Top View). 13/32" 0.177" diameter 3/8"...
- Page 10 CO2075FF — Ice Maker/Refrigerator 5. Remove the top handle and discard. (This handle will be replaced with the Modified Handle included in the Full Overlay Door Panel Kit.) 6. Remove the two screws located on both sides of the lower handle. Remove the handle.
- Page 11 1. Remove the existing hinges from the unit, saving the door closure assembly. 2. Install the new Replacement Top Hinge onto the unit (see Figure 24). 02/2005 CO2075FF — Ice Maker/Refrigerator Door Panel Wood Panel Top Hinge Plate (5/8" Longer than Existing Top Hinge Plate) #10 x 5/8"...
-
Page 12: Checking Door Alignment
CO2075FF — Ice Maker/Refrigerator 5 Adjust Door Checking Door Alignment The unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top (see Figure 26). -
Page 13: Water Supply Connection
(see Figure 32). However, make certain that the tubing is not pinched or damaged during installation. • U-Line recommends the use of copper tubing for installation. To connect to water supply: 1. Install the 1/4 inch OD copper water line from the main water source (see Figure 30). -
Page 14: Electrical Specifications
CO2075FF — Ice Maker/Refrigerator 7 Prepare Power Supply Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current). -
Page 15: Installation Of The Co2075Ff
Relocating the Shelves Both the glass shelves in the refrigerator and the inner door shelves can be moved to accommodate your bottles, cans and containers. Glass Shelves on Right-Hand Hinge Units 1. -
Page 16: Initial Start-Up
(24) hours of operation. CAUTION • The ice bucket MUST be fully inserted to avoid freezing products in the refrigerator section. The ice bin door must be fully closed with the door lip inside the ice bucket. • Do not place cans or bottles so they are touching the back wall of the refrigerator section, as they may freeze. -
Page 17: Service Information
For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in undercounter icemakers, Combo ®...