Related Manuals for Norton clipper CFP13 W B
Summary of Contents for Norton clipper CFP13 W B
- Page 1 CFP13 W B COMPACTORS OPERATING INSTRUCTIONS Translation of the original Instructions...
- Page 2 VERS. 2023.03.15 CFP13 W B _MAN_ EN...
- Page 3 SAINT - GOBAIN ABRASIVES S.A. 190, BD. J. F. KENNEDY L-4930 BASCHARAGE Declares that this product: CFP13 W B 70184632594 Norton Clipper Compactors Code: Is in conformity with the following Directives: "MACHINES" 2006/42/CE "NOISE" 2000/14/CE And European standard : •...
- Page 4 VERS. 2023.03.15 CFP13 W B _MAN_ EN Declaration of conformity The undersigned manufacturer: SAINT - GOBAIN ABRASIVES S.A. 190, BD J.F. KENNEDY L- 4930 BASCHARAGE Declares that this product: Compactor CFP13 W B Code: 70184608007 is in conformity with the following standard: •...
-
Page 5: Table Of Contents
VERS. 2023.03.15 CFP13 W B _MAN_ EN Norton Clipper CFP 13 W B OPERATING INSTRUCTIONS TABLE OF CONTENTS 1 BASIC SAFETY INSTRUCTIONS 1.1 Symbols 1.2 Machine plate 1.3 Safety instructions for particular operating phases 2 MACHINE DESCRIPTION 2.1 Short description 2.2 Purpose of use... -
Page 6: Basic Safety Instructions
CFP13 W B _MAN_ EN 1 BASIC SAFETY INSTRUCTIONS The Norton Clipper CFP13 W B is exclusively designed for compaction mainly on construction sites. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer shall not be held responsible for any resulting damage. Any risk shall be borne entirely by the user. -
Page 7: Machine Plate
VERS. 2023.03.15 CFP13 W B _MAN_ EN Machine plate Important data can be found on the following plate located on the machine: Machine code Machine model Serial number Year of production Machine Weight Safety instructions for particular operating phases Before starting the work •... - Page 8 VERS. 2023.03.15 CFP13 W B _MAN_ EN CLIMBING ABILITY...
-
Page 9: Machine Description
The compactor CPF13 W B is suitable for repairing asphalted surfaces, for small compacting jobs and for preparing green areas As with all other NORTON products, the operator will immediately appreciate the attention given to detail and quality of materials used in construction. The machine and its component parts are assembled to high standards assuring long life and minimum maintenance. - Page 10 VERS. 2023.03.15 CFP13 W B _MAN_ EN Handle (1) Jig welded steel construction is connected by 4 shockmount on the frame of the machine to reduce the vibrations reach the operator Belt drive and belt cover (2) A centrifugal clutch inside the engine pulley drives the gear shaft through V-Belts. It allows to gradually engaging the vibration of the machine.
-
Page 11: Technical Data
VERS. 2023.03.15 CFP13 W B _MAN_ EN Technical DATA Model CFP13 W B Dimensions plate mm 420 x 550 Width x Length Operation weight 93 kg Working speed 22 m/min Max climbing ability Frequency 90 Hz Centrifugal force 13 kN Transmission Centrifugal clutch / belt Engine... -
Page 12: Commissioning
VERS. 2023.03.15 CFP13 W B _MAN_ EN 3 COMMISSIONING User’s reference guide... -
Page 13: Battery's Fixation And Starting Up The Machine
VERS. 2023.03.15 CFP13 W B _MAN_ EN Battery’s fixation and starting up the machine • Switch on the battery by pressing the Power button (1) (the switch must be in the OFF position) the 3 LEDs will lit. • Wait until the green LED on the control panel is the only one lit •... -
Page 14: Charging The Battery
VERS. 2023.03.15 CFP13 W B _MAN_ EN Charging the battery This machine works with a battery, so you have to think about charging it. A fast charger is available for this. It will take between 1h and 1h30 to recharge a full battery charge. When charging the battery, the charger fan turns on to prevent the battery from heating up. -
Page 15: Operating The Machine
VERS. 2023.03.15 CFP13 W B _MAN_ EN 4 OPERATING THE MACHINE Site of work • Remove from the site anything, which might hinder the working procedure! • Make sure the site is sufficiently well lit! • Make sure you have a continual adequate view of the working area so you can intervene in the working process at any time! •... -
Page 16: Maintenance Of Egx Pack Honda
VERS. 2023.03.15 CFP13 W B _MAN_ EN Maintenance of eGX Pack Honda... -
Page 17: Fault : Causes And Cures
VERS. 2023.03.15 CFP13 W B _MAN_ EN 7 FAULT CAUSES AND CURES Fault –finding procedures Should any fault occur during the use of the machine, turn it off. Any works dealing with the engine of the machine can only be carried out by a qualified technician. Troubles-shooting guide TROUBLE POSSIBLE CAUSE... -
Page 18: Customer Service
Spare parts for the motor can be ordered with the manufacturer of the motor or with their dealer, which is often quicker and cheaper. This machine has been manufactured by: Saint-Gobain Abrasives S.A. 190, Bd. J. F. Kennedy L- 4930 BASCHARAGE Grand-duché de Luxembourg. Tel.: 00352-50 401-1 Fax: 00352- 50 16 33 http://www.construction.norton.eu e-mail: sales.nlx@saint-gobain.com... -
Page 19: Spare Parts
VERS. 2023.03.15 CFP13 W B _MAN_ EN Spare parts In order to consult the spare parts lists, we invite you to visit the after-sales website of Norton Clipper by using the following address: https://spareparts.nortonabrasives.com For a quick access, you can also use the QR Code shown below using your mobile phone: This electronic catalogue provides exploded views and spare parts lists for different machines designed by Norton Clipper so you can find references you need. - Page 20 VERS. 2023.03.15 CFP13 W B _MAN_ EN...