Advertisement
• Motor specifications:
B
Number of phases (1 single phase or 3 three-phase)
C
Nominal voltage in volts (value, range or commutation)
D
Frequency (Hertz)
E
Nominal rating (Watts)
F
Rating of the fuse of the mains cable (Amperes)
1) Three-phase motor
• A standard wall socket with 3 poles + Earth, rated at 20A com-
pliant with IEC60309 will be required and a matching watertight
plug fitted to the power supply cable.
This appliance must be earthed with a green/yellow wire.
• Check the direction of rotation:
- of the planet gear, anti-clockwise direction
head)
- of the tool, clockwise direction.
• If the direction of rotation is reversed, change over the two
phase wires on the plug.
• Connection is made at higher voltage
connections to lower voltage supplies
follows:
- Unplug the machine.
- Remove the rear plate.
- Refer to the wiring diagram in § 6.6.
Use and Safety
Clean the machine properly prior to its first use
Uncontrolled closure of the lid or ram press involves a risk of crushing the fingers.
Never put a hand in the work area while the machine is in operation; risk of injury. It is strictly forbidden
to put the safety systems out of action or modify them: Risk of permanent injury!!!!
Check that the safety devices operate correctly each time before using (see paragraph on «safety system checks»).
Never put a hand, a hard or frozen object in the appliance
For health and safety reasons, always use a strong washable or disposable head covering that covers the hair completely.
3.
OPERATION - SAFETY
1
• The user's safety is ensured by:
- The motor stopping on opening the protection screen.
- The design of the screen which allows products to be added
while working in complete safety.
- The motor stopping on lowering the cradle. It will not start again
by pressing the START button.
- The START button needing to be pressed after a stoppage
("voltage loss" device).
- The motor being protected against overload by a thermal sensor.
- Following the instructions in this manual for using, cleaning
and maintaining the machine.
• Control panel
A Reduce time setting on timer
B Increase time setting on timer
C STOP button
D START button
E Timer display
Do not use the machine without the bowl.
2.
3a
2.
3b
(see arrow on
for 400V). For
230V proceed as
3.
1
- Change over the integral plate wire by moving the cable lug
from the terminal marked for the higher voltage (400V) onto
that for the lower voltage (230V).
- Change over the plate straps on the terminal plate.
- Check the direction of rotation and refit the plate.
2) Single phase motor
• A standard single phase wall socket with 2 poles + earth, rated
at 10/16 A will be required.
• The direction of rotation is factory-set.
To PAT test the Electrolux Range of Food Preparation Equipment,
the PCB board needs to be disconnected before any test is done.
This is due to the fact that the boards are fitted with a grounding
diode that can give incorrect result during such a test. Also on a
standard appliance a flash test of 25 amps and up to 3000v is
used but, as you would expect, to use this on equipment, which
has a printed circuit, board would be quite destructive to that
board. We would recommend the use of a PAT tester approved
for computer systems which use a lower rate of amps.
The appliance is perfectly safe and is CE certificated. There are
two ways to get overcome this problem.
· Disconnect the board as instructed and test using test for PC's,
· Or install the mixer on a fused spur (no plug) as this takes it
away from being a portable appliance and the PAT test is then
not needed.
ATTENTION!!
• The beaters are normally started if the bowl support cradle
assembly is in the working position.
- The protection screen is fitted and closed.
- The timer is set to continuous or timed operating mode.
- The bowl is in position on the cradle.
a) Timed operation
- Select time on E by pressing buttons A and B
- Start by pressing button D
- Stop at the end of the time set, or by pressing button C.
Note:
- To change the time being counted down, press on
button C then change using buttons A and B;
resume cycle by pressing button D.
- The time displayed at the beginning of the cycle remains in
memory
- To permanently interrupt a cycle underway, press button C twice.
b) Continuous operation
- Select --- on E by pressing and holding button A
- Start by pressing button D
- Stop by pressing button C
3
2.
3c
XBM20/30 GB 09 2023
Advertisement
