Gaggia Velasca, RI8260 - Superautomatic Coffee Machine Manual

General description

1. Coffee bean hopper lid
2. Coffee bean hopper
3. Power cord socket
4. Water tank
5. Pre-ground coffee compartment
6. Grinder adjustment knob
7. Control panel
8. Coffee grounds container
9. Coffee dispensing spout
10. Drip tray
11. Drip tray cover
12. Drip tray full indicator
13. Espresso button
14. Espresso lungo button
15. Aroma strength button
16. Standby button
17. Menu button
18. Hot water button
19. Steam button
20. Power supply cord
21. Cleaning brush (for specific types only)
22. Grease for the brew group (for specific types only)
23. Pre-ground coffee measuring spoon
24. Water hardness test strip
25. Coffee residues drawer
26. Brew group
27. Hot water/steam dispensing spout
28. Classic milk frother

Important

Read and follow the safety instructions carefully and only use the machine as described in this user manual to avoid accidental injury or damage due to improper use of the machine. Keep this user manual for future reference.

Warning

• Check if the voltage indicated on the machine corresponds to the local voltage before you connect the machine
• Connect the machine to a grounded wall outlet.
• Do not let the power supply cord hang over the edge of a table or counter, or touch hot surfaces.
• Never immerse the machine, power plug or power supply cord in water (danger of electrical shock).
• Do not pour liquids on the power supply cord connector.
• Never direct the hot water jet towards body parts: danger of burns.
• Do not touch hot surfaces. Use handles and knobs.
• Remove the power plug from the wall outlet:
• If a malfunction occurs.
• If the machine will not be used for a long time.
• Before cleaning the machine.
• Pull on the power plug, not on the power supply cord. Do not touch the power plug with wet hands.
• Do not use the machine if the power plug, the power supply cord or the machine itself is damaged.
• Do not make any modifications to the machine or its power supply cord. Only have repairs carried out by a service center authorized by Philips to avoid a hazard.
• The machine should not be used by children younger than 8 years old.
• This machine can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the machine in a safe way and understand the hazards involved. Children shall not play with the machine. Cleaning and user maintenance shall not be made by children unless they are 8 years and above and supervised.
• Keep the appliance and its power supply cord out of reach of children aged less than 8 years.
• Do not spill water on the power plug.
• Only use the machine as described in the user manual to avoid potential injury due to misuse.
• Never insert fingers or other objects into the coffee grinder.

Caution

• As water is a foodstuff, the water in the water tank must be used up within 1 to 2 days.
• If you are not going to use your coffee machine for a prolonged period (e.g. a holiday), we recommend that you discard any water left inside the tank. Before you use the coffee machine again, clean the water tank and perform a manual rinsing cycle.
• Do not put any of the detachable parts of the machine in the dishwasher, except for the milk carafe.
• The machine is for household use only. It is not intended for use in environments such as canteens, staff kitchen of shops, offices, farms or other work environments.
• Always put the machine on a flat and stable surface.
• Do not place the machine on hot surfaces, directly next to a hot oven, heater or similar source of heat.
• Only put roasted coffee beans into the coffee bean hopper. If ground coffee, instant coffee, raw coffee beans or any other substance is put in the coffee bean hopper, it may damage the machine.
• Let the machine cool down before inserting or removing any parts.
• Never use warm or hot water to fill the water tank. Use cold nonsparkling drinking water.
• Never clean with scrubbing powders or harsh cleaners. Simply use a soft cloth dampened with water.
• Descale the machine regularly. The machine indicates when descaling is needed. If you do not clean and descale the machine, you run the risk that the machine stops working and that your guarantee becomes invalid.
• Do not keep the machine at temperatures below 32°F. Water left in the heating system may freeze and cause damage.
• Do not leave water in the tank when the machine is not used over a long period of time. The water can get contaminated. Use fresh water every time you use the machine.

Electromagnetic fields (EMF)

This machine complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

The display

Some buttons can be used to navigate through the menus:
	ESPRESSO button = ESC button: you can press this button to return to the main menu. The ESC button takes you back one level. You may have to press the ESC button. several times to get back to the main menu.
	AROMA STRENGTH button = OK button: you can press this button to select, confirm or stop a function.
	STEAM button = UP button: press this button to scroll up through the display menu
	MENU button = DOWN button: press this button to scroll down through the display menu.

First installation

1. Slide the drip tray with drip tray cover into the machine.
2. Remove the water tank.
3. Fill the water tank to the MAX level with fresh water.
4. Fill the coffee bean hopper with coffee beans.
5. Insert the small plug into the socket located on the back of the machine. Insert the mains plug into the wall socket.
6. Attach the classic milk frother to the hot water/steam dispensing spout.
7. Place a container under the classic milk frother.
8. Press the STANDBY button to switch on the machine.
9. Press the OK button to start the automatic circuit priming cycle.
   • The machine performs an automatic rinsing cycle.
10. Remove the water tank from the machine and empty it.
11. Fill the water tank with fresh water and place it back into the machine.
12. Continue with the next step: the manual rinsing cycle.

Manual rinsing cycle

1. Place a container under the coffee dispensing spout.
2. Press the AROMA STRENGTH button to select pre-ground coffee. Do not add pre-ground coffee.
3. Press the ESPRESSO LUNGO button. The machine starts dispensing water.
4. When the machine stops dispensing, empty the container. Repeat steps 1-3 twice.
5. Place a container under the classic milk frother.
6. Press the HOT WATER button. Hot water dispensing starts automatically.
   Dispense water until the display shows the no water icon.
7. Fill the water tank with fresh water up to the MAX level and remove the container.

The machine is ready for use.

Water filter

The Intenza+ water filter is designed to reduce limescale deposits in your coffee machine and provide filtered water to preserve the aroma and flavor of each cup of coffee.

Installing the water filter

1. Remove the small white filter from the water tank and store it in a dry place.
   Note: Please keep the small white filter for future use. You will need it for the descaling process.
2. Remove the filter from its packaging and immerse it in cold water with the opening pointing upwards. Press the sides of the filter gently to let out the air bubbles.
3. Place the filter in the empty water tank. Press it down until it cannot move any further.
4. Fill the water tank with fresh water up to the MAX indication and place it the machine.
5. Select the hot water function and dispense hot water until the water tank is empty (see chapter 'Using the machine', section 'Brewing special drinks').
6. Refill the water tank with fresh water up to the MAX indication and place it back into the machine.
7. Press the MENU button to enter the menu.
8. Press the DOWN button until the display shows the following icon.
   
9. Press the UP button to select 'ON' and press the OK button to confirm.
   
10. Press the ESC button.

The filter and machine are now ready for use.

Replacing the water filter

• The display shows the following icon to indicate the water filter needs to be replaced.
  
  1. Replace the filter as described in section 'Installing the water filter'.
  2. Press the MENU button and press the UP/DOWN button to scroll trough the options on the menu until the following icon is displayed.
  3. Select the RESET option and press the OK button to confirm.
     
  4. Press the ESC button to exit.

If the filter is already installed and you want to remove it and not replace it, choose OFF

Measuring the water hardness

To be able to adjust the machine settings to the water in your region, please measure the water hardness with the water hardness strip supplied.

1. Immerse the water hardness test strip (supplied with the machine) in fresh water for 1 second.
   
2. Remove the water hardness strip and and wait for 1 minute.
3. Check how many squares have changed into the red color and check the water hardness in below table.
   

Setting the water hardness

1. To set the water hardness, press the MENU button, select menu and scroll to select water hardness.
2. Press the OK button and select the water hardness in your area.
3. Press the OK button to confirm.
4. Press the ESC button to return to the main menu.

Using the machine

Brewing coffee with beans

1. Adjust the coffee dispensing spout to suit the size of your cup.
2. Press the AROMA STRENGTH button to select the desired coffee strength from 1-5 beans.
3. Press the ESPRESSO button to brew an espresso or press the ESPRESSO LUNGO button to brew a coffee.

Brewing coffee with pre-ground coffee

When you brew coffee with pre-ground coffee, use the measuring scoop in the multifunctional tool supplied to put the correct dose in the pre-ground coffee compartment. If you add more pre-ground coffee, the excess coffee will end up in the coffee grounds drawer.

1. Open the lid of the pre-ground coffee compartment.
2. Pour one measuring scoop of pre-ground coffee into the compartment.
   
   Do not put any other substance than pre-ground coffee in the pre-ground coffee compartment, as this may damage the machine.
3. Place the lid back on the pre-ground coffee compartment.
4. Place a cup under the coffee dispensing spout.
5. Press the AROMA STRENGTH button to select pre-ground coffee.
6. Press the ESPRESSO button.
   • The machine starts brewing coffee.

Note: You can only brew one coffee beverage at a time with preground coffee.

Adjusting the coffee quantity

1. Press and hold the ESPRESSO button or ESPRESSO LUNGO button until the display shows the word MEMO.
2. When the cup contains the desired amount of coffee, press the OK button to save the selected quantity.

Adjusting the grind setting

1. Open the coffee bean hopper.
2. Place the end of the measuring spoon handle on the grinder adjustment knob in the coffee bean hopper. Use the spoon to press and turn the knob to the left or to the right one notch a time.
3. There are 10 different grinding degree settings you can choose from. The smaller the dot, the stronger the coffee.
   • Coarse grind: lighter taste, for dark roasted coffee blends.
   • Fine grind: bolder taste, for light roasted coffee blends.
4. Place the coffee bean hopper back.
5. Brew 2-3 coffees to taste the difference.

Frothing milk

Danger of scalding. Only grab the steam wand by its protective handle. Dispensing may be preceded by small jets of hot water.

1. Fill 1/3 of a jug with cold milk.
2. Immerse the classic milk frother in milk. Press the STEAM button.
3. Froth the milk by gently swirling the jug and moving it up and down.
4. Press the OK button to stop frothing.

Hot water

Danger of scalding. Only grab the steam wand by its protective handle. Dispensing may be preceded by small jets of hot water.

1. Place a jug under the classic milk frother.
2. Press the HOT WATER button. Hot water dispensing starts automatically.
3. Press the OK button to stop hot water dispensing. Remove the container.

Descaling

You have to descale the machine when the display shows the CALC CLEAN icon.

If you do not descale when the display shows the CALC CLEAN icon, the machine may stop working properly. In this case, repairs are not covered by the warranty.

Never drink the water with descaling mixture that you pour into the water tank or any water with residues that comes out of the machine during the descaling procedure.

The descaling procedure lasts approximately 30 minutes. Only use the Gaggia solution to descale the machine. The Gaggia descaling solution is designed to ensure optimal performance of the machine.

Descaling procedure

You can pause the descaling or rinsing cycle by pressing the ESC button. The display will show the following icon. To continue the descaling or rinsing cycle, press the OK button.

1. Remove and empty the drip tray. Slide the drip tray back into the machine.
2. Remove the water filter from the water tank (if present).
3. Remove the classic milk frother from the steam wand.
4. Press the OK button.
5. The display shows the following icon to indicate that the machine enters the descaling cycle. If you want to exit the descaling cycle, press the ESC button.
   
6. Pour the entire bottle of Gaggia descaling solution (250ml) into the water tank.
7. Add water to the descaling solution in the water tank up to the CALC CLEAN indication.
8. Place a large container (1.5 l) under the steam wand and dispensing spout.
9. Press the OK button to start the descaling cycle.
   • The machine dispenses the entire descaling solution at regular intervals through the steam wand and dispensing spout (this takes approximately 25 minutes).
10. Wait until all of the descaling solution has been dispensed. Remove and empty the container.
11. Remove and empty the drip tray. Slide the drip tray back into the machine.
12. Rinse the water tank and fill it with fresh water up to the CALC CLEAN indication. Slide the water tank back into the machine.
13. Place the container back under the steam wand and dispensing spout.
14. Press the OK button to start the rinsing cycle (this takes approximately 4 minutes).
    • The display shows the following icon to indicate that the rinsing cycle is finished.
      
15. The display shows a tick icon.
16. Rinse the water tank and fill it with fresh water up to the MAX level. Place the water tank back into the machine.
17. Press the OK button to return to the main menu.
18. The display shows the following icon to indicate that the machine is heating up.
    
    • The machine performs an automatic rinsing cycle.
19. Remove the container. Remove and empty the drip tray. SLide the drip tray back into the machine.
20. Place the water filter back in the water tank. Reinsert the classic milk frother.
21. Remove and rinse the brew group see chapter 'Cleaning and maintenance', section 'Clean the brew group'.

The machine is now ready for use.

Interruption of the descaling cycle

Once the descaling cycle has started, you must complete it till the very end without turning off the machine. In case you get stuck during the cycle or in case of power failure or accidental disconnection of the power cord, you can exit by pressing the standby button. If this occurs, empty and rinse carefully the water tank, then fill it up to the CALC CLEAN level. Follow the instructions in chapter 'First installation', section 'Manual rinsing cycle' before brewing any beverage. If the cycle was not completed, the machine will require another descaling cycle to be performed at your earliest convenience.

Cleaning and maintenance

Weekly cleaning of the brew group

Clean the brew group once per week.

1. Remove the coffee grounds container and open the service door.
2. Remove the coffee residues drawer.
   
3. To remove the brew group, press the lever and pull the brew group out of the machine.
4. Rinse the brew group with fresh water and let it air dry.
   
   
5. To place the brew group back, make sure that the lever is in contact with the base of the brewing unit.
   
   Note: If it is not in contact with the base, push it down.
6. Make sure the locking hook of the brew group is in the correct position. To position the hook correctly, push it upwards until it is in uppermost position.
   
7. The hook is not correctly positioned if it is still in bottom most position.
   
8. Slide the brew group back into the machine along the guiding rails on the sides until it clicks into position. Then place the coffee residues drawer back in the machine.

Lubrication

Lubricate the brew group after approximately 500 cups of coffee or once a month.

1. Apply some lubricant around the shaft in the bottom of the brewing unit.
   
2. Apply lubricant to the rails on both sides, as shown in the illustration.
3. Slide the brew group back into the machine along the guiding rails on the sides until it clicks into position. Then place the coffee residues drawer back in the machine.
   

Classic milk frother cleaning (daily)

Remove the external part of the classic milk frother and rinse it with fresh water.

Classic milk frother and steam wand cleaning (weekly)

1. Remove the external part of the classic milk frother and rinse it with fresh water.
   
2. Remove the upper part of the classic milk frother from the steam wand and rinse it with fresh water.
3. Clean the steam wand with a wet cloth.
4. Reassamble all the classic milk frother parts.
   

Warning icons and error codes

Warning signals are displayed in red.
Below you find a list of the warnings that may appear on the display and their meaning.

	Fill the water tank with fresh water to the MAX level indication.
	The bean hopper is empty. Put new coffee beans in the bean hopper.
	The brew group is not in the machine. Insert the group.
	Close the service door.
	Remove the coffee grounds container and empty it.
	There is too much powder in the brew group. Clean the brew group.
	You forgot to place the lid on the coffee bean hopper. If you do not place it back within 30 seconds the display will return to the main menu and the brewing cycle will be stopped.
	If an error code is triggered, check the section ‚Meaning of error codes' to see what the code on the display means and what you can do. The machine cannot be used when this icon is on the display.

Meaning of error codes

If the above solutions do not help to remove the error code icon from the display and bring the machine back to normal working order, contact the Gaggia hotline.
Contact details can be found in the warranty booklet or or visit
www.gaggia.com/n-m-co/espresso/world-wide or www.gaggia.it/n-m-co/espresso/contact.

Troubleshooting

Note: If you are unable to solve the problem with the information in this table, contact your local reseller or an authorized service center. Contact details are included in the warranty booklet supplied separately or visit
www.gaggia.com/n-m-co/espresso/world-wide or www.gaggia.it/n-mco/espresso/contact.

Warranty and support

If you need information or support, please visit www.gaggia.com/n-m-co/espresso/world-wide or www.gaggia.it/n-m-co/espresso/contact, or read the separate international warranty leaflet.

Important safeguards

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.
7. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Always attach plug to appliance first, then plug cord into wall outlet. To disconnect, turn any control to "off", then remove plug from wall outlet.
12. Do not use appliance for other than intended use.

SAVE THESE INSTRUCTIONS

Caution

This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only.

1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage.
2. Never use warm or hot water to fill the water tank. Use cold water only.
3. Keep your hands and the cord away from hot parts of the appliance during operation.
4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft cloth dampened with water.
5. For optimal taste of your coffee, use purified or bottled water. Periodic descaling is still recommended every 2-3 months.
6. Do not use caramelized or flavored coffee beans.

Instructions for the power supply cord

• A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.
• Longer detachable power-supply cords or extension cords are available and may used if care is exercised in their use.
• If a long detachable power-supply cord or extension cord is used.
  1. The marked electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance.
  2. If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and
  3. The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Gaggia Velasca, RI8260 - Superautomatic Coffee Machine Manual