Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for eltherm ELTC/L-15
Summary of Contents for eltherm ELTC/L-15
- Page 1 OPERATION- MANUAL ELTC/L-15 Temperature controller up to 999°C with ramp mode as tabletop unit eltherm GmbH P.: +49 2736 4413-0 BU-108 F.: +49 2736 4413-50 Ernst-Heinkel-Strasse 6 -10 Revision 1 57299 Burbach, Germany info@eltherm.com www.eltherm.com...
-
Page 2: Table Of Contents
Notes on commissioning RAMP MODES Declaration of Conformity NOTES DOWNLOADS For proper and safe use of the ELTC/L-15 temperature cont- roller, please follow these instructions. Please keep these instructions for future reference (e.g. in the system documentation). RESERVATION Subject to technical changes. Changes, errors and misprints do not constitute grounds for claims for damages. -
Page 3: Introduction
For more information on the disposal and recovery of waste electrical and electronic equipment (WEEE) and collection points, please contact your local waste management com- pany or the manufacturer from whom you purchased the product. Contact us: +49 2736 4413-0 • info@eltherm.com www.eltherm.com... -
Page 4: Functional Description & Technical Data
If the actual value (P01) falls below the setpoint (P10 minus hysteresis P11), relay K1 switches the heating on. In the event of sensor errors, relay K1 switches the heating line off or on, depending on the configuration of the controller. TECHNICAL DATA ELTC/L-15 (Art. 0621501) Nominal voltage 90…260 VAC, 50/60 Hz... -
Page 5: Connection Plan
NOTE After switching on the controller, the display shows the current actual value. Contact us: +49 2736 4413-0 • info@eltherm.com www.eltherm.com... -
Page 6: Operation
OPERATION OPERATING PANEL LEDs in Display "1" = Control relay ON "2" = Ramp ON "4" = Alarm relay activated (=switched OFF) A flashing of the LEDs indicates a function delay. Keys " " = Increase values " " = Decrease values "P"... -
Page 7: Parameters And Their Meaning
Ramp setpoint 1 Nop=inactive 1..999 Min., [30 Min], Time for rampe 1 Nop, 0...950°C [100°C] Ramp setpoint 2 1..999 Min., [30 Min], Time for rampe 2 Nop, 0...950°C [100°C] Ramp setpoint 3 Contact us: +49 2736 4413-0 • info@eltherm.com www.eltherm.com... -
Page 8: Notes On Commissioning
RAMP MODES Notes on commissioning ATTENTION Ramp start The settings of the controller must be checked during Press the „ " key for >5 seconds, LED „2“ lights up continuous- commissioning. ly.If the current temperature is below the value stored for P50, it is first heated up to this value. -
Page 9: Declaration Of Conformity
Parameter Own settings Declaration of Conformity We declare that the described product fully complies with Di- rectives 2014/35/EU, 2014/30/EU and 2011/65/EU. If you need a detailed declaration of conformity, please contact us. Contact us: +49 2736 4413-0 • info@eltherm.com www.eltherm.com... -
Page 10: Downloads
DOWNLOADS You can find helpful downloads for this or other products under the following link: https://eltherm.com/downloads eltherm GmbH Headquarters Ernst-Heinkel-Straße 6 -10 57299 Burbach, Germany T.: +49 2736 4413-0 F.: +49 2736 4413-50 info@eltherm.com www.eltherm.com...
Need help?
Do you have a question about the ELTC/L-15 and is the answer not in the manual?
Questions and answers