Safety Precautions; Installation Instructions; Installation Diagram - Olmo Inventa Series User And Installation Manual

2. Back-light function
Hold down any button on remote control to activate
the back light. It automatically shuts off 10 seconds
later.
Note: Back-light is an optional function.
3. Auto Restart Presetting
The air conditioner has an Auto-Restart function.
Safeguarding the environment
This appliance is made of recyclable or re-usable
material. Scrapping must be carried out in
compliance with local waste disposal regulations.
Before scrapping it, make sure to cut off the mains
cord so that the appliance cannot be re-used.
For more detailed information on handling and
recycling this product, contact your local
authorities who deal with the separate collection
of rubbish or the shop where you bought the
appliance.
SCRAPPING OF APPLIANCE
This appliance is marked according
to the European Directive 2012/19/EC,
Waste Electrical and Electronic
Equipment (WEEE).
This marking indicates that this
product should not be disposed with
other household wastes throughout
the EU. To prevent possible harm to
the environment or human health from
uncontrolled waste disposal,recycle it
responsibly to promote the sustainable reuse of
material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was
purchased. They can take this product for
environmental safe

Safety precautions

Symbols in this Use and Care Manual are
interpreted as shown below.
Be sure not to do
Pay attention to such a situation.
Warning: Incorrect handling could cause a
serious hazard, such as death, serious injury, etc.
Use correct power
supply inaccordance
with the rating plate
requirement.
It is harmful to your
Otherwise, serious
health if the cool air
faults or hazard may
reaches you for a long
occur or a fire maybe
time. It is advisable to
break out.
let the air flow be
deflected to all the
ON
OFF room.
Keep the power
supply circuit
breaker or plug from
dirt. Connect the
power supply cord to
it firmly and correctly,
Prevent the air flow
lest an electric shock
from reachingthe gas
or a fire break out
burners and stove.
due to insufficient
contact.
of Remote Control
recycling.
.
Grounding is essential.
Never insert a stick or
similar obstacle to the
unit. Since the fan
rotates at high speed,
this may cause an injury.
Do not repair the
appliance by yourself.
If this is done
incorrectly, it may cause
an electric shock, etc.
(optional)
ON
OFF
Do not use the power
supply circuit breaker
or pull off the plug to
turn it off during
operation. This may
cause a fire due to
spark, etc.
It is the user's
responsibility to
make the appliance
be grounded
according to local
codes or ordinances
by a licenced
technician.

Installation instructions

Installation diagram

Distance from wall
should be over
50mm
Distance from the obstacle
should be over 3000mm.
Distance from floor
over 2500mm.
Air intake distance
from the wall
should be
over 250mm
Above figure is only a simple presentation
of the unit, it may not match the external
appearance of the unit you purchased.
Installation must be performed in accordance with
the national wiring standards by authorized personnel only.
2
Do not touch the
Do not put any objects
operation buttons
on the outdoor unit.
when your hands
are wet.
ON
OFF
SMART MODE
TEMP.
SUPER FAN SPEED
TEMP.
FEEL SLEEP
CLOCK TIMER ON TIMER OFF
QUIET DIMMER ECONOMY
Turn off the Do not knit, pull or
applianceby remote
press the power supply
control firstly before cord, lest the power
cutting off power
supply cord be broken.
supply if malfunction An electric shock or fire
occurs.
is probably caused by
a broken power supply
cord.
Distance from ceiling should be
over 200 mm
should be
Distance from the
obstacle should be
over 500mm.
Distance from
the wall should
be over 50mm
Air intake
distance from
the wal
should be
over 250mml
over 250mm