Related Manuals for Olmo OSH-T24HRK3
Summary of Contents for Olmo OSH-T24HRK3
- Page 1 MODEL: OSH-T24HRK3/OSH-OU24HRK3 OSH-T36HRK3/OSH-OU36HFK3 OSH-T48HRK3/OSH-OU48HFK3 OSH-T60HRK3/OSH-OU60HFK3...
-
Page 2: Table Of Contents
CONTENTS PRECAUTIONS FUNCTION AND OPERATION OF PANEL'S PARTS DISPLAY PANEL INDOOR UNIT INSTALLATION DRAINAGE PIPE INSTALLATION INSTALLATION OF PANEL OUTDOOR UNIT INSTALLATION REFRIGERANT PIPE INSTALLATION AIR PURGING CHARGE ADDITIONAL REFRIGERANT ELECTRIC WIRING TEST RUN ADJUSTING AIR FLOW DIRECTION MAINTENANCE IMPORTANT SAFETY INFORMATION TROUBLES AND CAUSES REMOTE CONTROLLER... -
Page 3: Precautions
PRECAUTIONS Read the following " PRECAUTIONS" carefully before installation. The caution items stated here must be followed because these important contents are related to safety. The meaning of each indication used is as below. Incorrect installation due to ignoring of the instruction will cause harm or damage, and the seriousness is classified by the following indications. - Page 4 Operating condition Noise pollution The protective device maybe trip and stop Install the air conditioner in a place the unit within temp range listed below: that can bear its weight in order to operate more quietly. Outdoor air temperature is over 24 Install the outdoor unit in a place Outdoor air temperature is below -7 HEATING...
-
Page 5: Function And Operation Of Panel's Parts
FUNCTION AND OPERATION OF PANEL'S PARTS Please adjust room temperature properly especially when the old men, children, patients stay at house. Lightning and other electromagnetic radiation may cause ill effect .If it is ,please plug off the power switch ,and replug in ,then restart the unit. Do not block the inlet of indoor unit or outlet of oudoor unit, any of blocks will reduce cooling or heating efficiency. -
Page 6: Display Panel
DISPLAY PANEL Infrared signal receiver: receive the signal from the remote controller. To make your remote controller operation more efficient, please let remote controller emittor aim at infrared signal receiver. Buzzer: firstly power supplied or any of remote controller operations will make the buzzer sound once. -
Page 7: Indoor Unit Installation
INDOOR UNIT INSTALLATION INSTALLATION LOCATIONS CAUTIONS 1.Location in the following places may cause malfunction of the machine. (If unavoidable, please consult your local dealer) a. A place where there is flammable gas leakage. b. There is salty air surrounding(near the coast). c. - Page 8 INDOOR UNIT INSTALLATION SHAPE OF INDOOR UNIT distance between hook and ceiling b.height of panel ceiling sponge c.distance between hook and indoor unit top d.distance between ceiling and indoor unit top e.height of indoor unit; A.dimension of panel B.dimension of ceiling cut-out C.dimension of indoor unit.
- Page 9 CEILING HOLE AND THE HOOK INSTALLATION Preparation Work on the Ceiling Installation method should be changed under the different construction structure. Please consult the professional for the detailed information. After opening a hole, the ceiling should be horizontal and strong to prevent vibration. Cut the beams at the hole and remove them.
-
Page 10: Drainage Pipe Installation
Install the hanging bolt into T groove of the hanging tool. Overhang the indoor unit and ensure it is level using a level indicator. Level Indicator Hanging Screw Bolt Hanging Ear Indoor Unit Ceiling 30mm Installation Plate Hanging Screw Bolt M10 f10 Gasket Locking Nut M10 Install it down the... - Page 11 1.5m~2m Bend Support Up and Down Lean Downward over 1/100 Fold As long as possible about (10mm) Lean Downward VP30 over 1/100 Drainage Pipe Material, Heat-insulating Material The listed material should be used: Drainage Pipe Polyvinyl chloride pipe (f32mm outer diameter) Material Heat Insulation Foamed polyethylene insulation plate (10mm thickness)
- Page 12 Heat Insulation Wrap the flexible hose carefully with the attached heat insulation material from the start to the end (to indoor part) Flexible Hose Hose band Field-arranged Polyvinyl Chloride Pipe Attached Heat-insulation Heat-insulation Material Material Drainage Upward To make sure that the drainage pipe would not be slanted downward, lead it upward to a height 360mm maximum, then downward lead it.
-
Page 13: Installation Of Panel
INSTALLATION OF PANEL ¾ Å ³ ö · ç Ã æ ° å µ Ä ° ² × ° ¾ Å ³ ö · ç Ã æ ° å µ Ä ° ² × ° BODY DIMENSION:830X230X830 830X310X830 Unload air-in grille Take off air-in grille Unload panel installation cap Screw down the bolts... - Page 14 BODY DIMENSION:574X250X574 Unload air-in grille Take off air-in grille ON/OFF Installation bolt hole INSTALLATION OF PANEL 1.Please screw M10 gasket and M6*20 bolt at the corner of indoor unit ,before screwing them fasten ,screw other two additional bolts which locates red bolt showing as figure and notice that the direction of red arrow on the electrical box aligns the one on the panel.
-
Page 15: Outdoor Unit Installation
OUTDOOR UNIT INSTALLATION Location for installing outdoor unit 1. Install it at a place where it is convenient for installation and well ventilated. 2. Keep the required distance away from the wall as reqiured on the previous page when carrying on installation. 3. -
Page 16: Refrigerant Pipe Installation
REFRIGERANT PIPE INSTALLATION CAUTION Ventilate the air if there was any refrigerant leakage during the installation. Leaked refrigerant will generate poisonous gas if meeting fire. Make sure there is no refrigerant leakage after the installation. Leaked refrigerant will generate poisonous gas if meeting fire. Allowed Length and Drop of Pipes Requirements are different when installing the outdoor unit. -
Page 17: Air Purging
The following figure only shows the assembly relationship of the indoor unit ,outdoor unit and refrigerant pipes. Please refer to the following figures to install. NOTE The throttle subassembly has been installed in the outdoor unit.. Use two spanners to connect the pipe with indoor/outdoor pipes to avoid the copper pipe cracking. Please pay attention to the connection orientation when connecting. -
Page 18: Charge Additional Refrigerant
indoor unit 3-way valve diagram refrigerantflow direction Connect to indoor unit 3-way valve Close position Connect to outdoor unit Valve spindle Exhaust mouth Exhaust nut Valve core Exhaust spindle outlet nut additional freon refrigerant pot Connect hose Air exhaust process: (6). -
Page 19: Electric Wiring
Specification of Max. length R410A Liquid pipe 6.35 (L-5)X0.022 kg (L-5)X0.03kg 9.52 (L-5)X0.054kg (L-5)X0.05kg 12.7 (L-5)X0.11kg (L-5)X0.10kg (* "L" refers to length of connection pipe.) The additional refrigerant should be charged from the service port of the 3-way valve when the appliance is operating in cooling mode. Do not allow air enter the refrigeration system while charging refrigerant. - Page 20 CAUTION Power cord is to be selected according to national regulations. Outdoor unit power cord should be selected and connected according to the outdoor unit installation manual. Wiring should be away from high temperature components, or the insulation layer of the wires may melt down.
- Page 21 Panel Wiring Connect the Swing Motor terminal block according to cassette indoor unit wiring diagram. Terminal Board Diagram Please refer to cassette indoor unit wiring for the wiring. Steps of external wiring connection 1. Remove air intake grille and electric box cover of indoor unit. 2.
-
Page 22: Test Run
3. External wiring diagrams Electric heater Power supply cord Power supply circuit breaker (prepared by user) Power supply Power supply circuit breaker(prepared by user) Power supply Defrost connecting cable Control connecting cable Outdoor Indoor unit unit Power supply connecting cable Power supply cord TEST RUN Before testing... -
Page 23: Adjusting Air Flow Direction
ADJUSTING AIR FLOW DIRECTION Cassette Type While the unit is in operation, you can adjust the air flow louver to change the flow direction an ralize the room temperature evenly. Thus you can enjoy it more comfortably. 1.Set the desired air flow direction. Push the SWING button to adjust the louver to the desired position and push this button aga maintain the louver at this position. - Page 24 Checks before operation CAUTIONS Check that the wiring is not broken off or disconnected. Check that the air filter is installed.(Some air-conditioners have no air filters) Check that the outdoor unit air outlet or inlet is not blocked. Before you clean the air conditioner, be sure to disconnect the power supply plug. Clean the air filter The air filter can prevent the dust or other particulate from going inside.In case of blockage of the filter,the working efficiency of the air conditioner may greatly decrease.
-
Page 25: Important Safety Information
IMPORTANT SAFETY INFORMATION CAUTION Do not attempt to install this unit by yourself.This unit requires installation by qualified persons. DANGER Do not attempt to service the unit yourself.This unit has no user serviceable components.Opening or removing the cover will expose you to dangerous voltage.Turn off the power supply will not prevent potential electric shock. -
Page 26: Troubles And Causes
These are not failures Room air is smelly. A bad odor comes from the air conditioner. Smells impregnated in the wall,carpet,furniture,clothing,or furs,are coming out. A white mist of chilled air or water is generated from the outdoor unit. CAUTION If any of the following conditions occur,stop the air conditioner immediately,set off the power switch, and contact the dealer. - Page 27 Error code Fault code of indoor unit Failure Error Code Failure description Remarks Indoor ambient sensor fault 1 Check whether the sensors are normal. Indoor coil sensor fault 2 Check whether the sensors are Outdoor coil sensor Connected. Faultsensor fault (if there is an outdoor control board) 1.View the fault code of outdoor unit.
- Page 28 Fault code of outdoor unit Lighting Flashing(1Hz) Extinguishing Solutions Priority Gree Blue Faults/States Phase-sequence error 1.Check whether the Power phase is normal. Phase-loss 1.Check whether the high High pressure protection pressure is normal. 1.Check whether the exhaust Exhaust temperature protection temperature is normal.
-
Page 29: Remote Controller
REMOTE CONTROLLER Button Function (TEMP UP) Increase the temperature or time by 1 unit (TEMP DN) Decrease the temperature or time by 1 unit CLOCK DISPLAY HEALTHY ON/OFF To switch the conditioner on and off. To select the fan speed of auto/low/mid/high ON/OFF SWING TIMER... - Page 30 Remote control DISPLAY Meaning of symbols on the liquid crystal display No. Symbols Meaning FEEL mode indicator HEALTHY TIMER COOLING indicator DEHUMIDIFYING indicator FAN ONLY OPERATION indicator HEATING indicator FEEL SPEED AUTOQUIET COOL POWERFUL SIGNAL RECEPTION indicator SWING DELAY HEAT HEALTHY TIMER TIMER OFF indicator...
- Page 31 Preliminary Instructions How to insert the batteries Remove the cover from the battery compartment , by sliding it in the direction of the arrow Insert the new batteries, ensuring that the (+) and (-) directions are correct Refit the cover by sliding it into place. Use 2 LRO 3 AAA (1.5V) batteries .
- Page 32 COOLING MODE COOL The cooling function allows the air condit- FEEL COOL SPEED AUTOQUIET COOL ioner to cool the room and at the same time POWERFUL reduces the humidity in the air. SWING DELAY HEAT To activate the cooling function ( COOL ) , press the HEALTHY TIMER MODE button until the symbol...
- Page 33 TIMER MODE----TIMER ON TIMER To set the automatic switching-on of FEEL SPEED AUTOQUIET COOL the air conditioner POWERFUL TIMER SWING DELAY HEAT To program the time start,the appliance should be off. HEALTHY TIMER Press TIMER , Set the temperature with pressing the ,Press TIMER Again , set the time with pressing the key , Press the key more times till...
- Page 34 FAN MODE The conditioner works in only FEEL SPEED AUTOQUIET COOL ventilation. POWERFUL SWING DELAY HEAT To set the FAN mode , Press MODE untill HEALTHY TIMER ( FAN ) appears in the display. Whith pressing button the speed changes ON/OFF in the following sequence: LOW/ MEDIUM/HIGH /AUTO in FAN mode.
- Page 35 FEEL MODE FEEL Automatic mode. FEEL FEEL SPEED AUTOQUIET COOL POWERFUL SWING DELAY HEAT To activate the FEEL (automatic) mode of operation, HEALTHY TIMER press the MODE button on the remote control until the symbol ( FELL ) appears in the display. In the FEEL mode the fan speed and the temperature ON/OFF are set automatically according to the room tempera-...
- Page 36 Air flow direction adjustment procedure Adjusting air flow direction Up/down direction can be adjusted by using the AIRFLOW button on the remote controller. Up/down direction can be adjusted by using the AIRFLOW button on the remote controller. This button,each time pressed,changes the mode in the following sequence: This button,each time pressed,changes the mode in the following sequence: AUTO push the LOUVER button,changes the mode to swing louver .