Accessories Available - HP 5326A Operating And Service Manual

Mode) 5326/27A
General Information
Table 1-3. Specifications (Continued)
Sample Rate:
FAST position: Continuously variable from less
than 100 pts to approximately 20 ms. NORM
position: Continuously variable from less than
20 ms to approximately 5 seconds. HOLD
position: Display can be held indefinitely.
Overt low:
Neon indicates when display range is exceeded.
Operating Temperature: 0° to 50°C
Power Requirements:
115 or 230 volts ±10%, 50 to 60 Hz, 70 watts
maximum
Weight:
Net, 16 lb.(7,4 kg). Shipping, 18 lb. 16 oz(8,7 kg)
Accessories Furnished:
Power Cord, 7% ft. Rack Mount Kit.
Dl^EMSIONS
ACCESSORIES AVAILABLE
HP 10503A, 50Q BNC Cable, 4 ft (122 cm)
HP 10532A, Extender Board Kit containing 2 ea.
15-pin extender 5060-0049, 1 ea. 18-pin
extender 5060-2041, and 1 ea. Amplifier
Extender, 10532-60001
IIP10542A, Remote Programming Interface
enables interfacing between the 5326/5327
Series counter with Option 004 and 40-bit
Output Register. Includes two (2) 7-bit
Digital-to-Analog Converters for level controls
and decoding for time base and function
selector.
HP Cable 562A-16C, 6 ft. (183 cm) to connect
5326/5327 Series with Option 003 to HP 5050B
or 5055A Digital Recorder
Option 001: 8-digit display
Option 002: Remote programming
Controls:
All front panel controls are single line program¬
mable except:
SEP-COM (separate-common) switch; the check
function is programmable
FAST/NORM Mode
Input Attenuators
AC/DC Input Signal Coupling
Control Signal:
Single line control using either contact closure to
ground or DTL drive on all lines except trigger
levels which are analog programmed (±3 Vdc)
Connector
Rear panel connector: HP 1251-0085; Amphenol
57-40300-375. (36-pin blue ribbon).
Mating connector: HP 1251-0084; Amphenol
57-30360-375
Option 003: Digital output (for numerals and
polarity only)
Code:
4-line 1-2-4-8 BCD, "1" state high. "0" state
+0.25 V at -1 tnA; "1" state: +5 V open circuit,
2.5 kQ source impedance nominal
Print Command:
+5 V to 0 V, dc coupled: occurs at end of gate.
Storage:
Buffer storage is provided so BCD output is
constant while next measurement is being
made
Inhibit Input:
Inhibits gate when instrument's cycle time is
less than the time required for external
equipment to interrogate BCD outputs.
Positive inhibit +5 Vdc
Connector:
Rear panel connector: HP 1251-0087;
Amphenol 57-40500-375 (50-pin blue ribbon).
Mating connector: HP 1251-0086; Amphenol
57-30500-375
Option 0G4: Remote Programming including
all signal input conditions.
Controls:
All front panel controls are programmable
except FAST/NORM Mode.
Control Signal:
Single line control using either contact
closure to ground or DTL drive on all lines
except trigger levels which are analog
programmable (±3 Vdc).
Connector:
Rear panel connector: HP 1251-0087;
Amphenol 57-40500-375 (50-pin blue ribbon)
Mating Connector: HP 1251-0086; Amphenol
57-30500-375