Page 1
ORIGINAL MADE IN ITALY OPERATING INSTRUCTIONS MASONRY SAWS BETJENINGSVEJLEDNING MASKINSAV TIL BYGGEARBEJDE...
Page 2
Battipav RPM A °C ART. 2,2kW / 3 hP 300 / 600 x 600 8085 230V 50Hz~ 2800 min 160°C 850 mm S6 40% 25,4 mm 2,2kW / 3 hP 300 / 600 x 600 80851 230V 50Hz~ 2800 min 160°C...
Page 3
Battipav LW = 79,8/0.0 dB(A) /mW(A) 720x1600x 1,15 m/s 85 mm 135 mm 60 mm LOP = 68,5 dB(A) 80 Kg 1000 mm (0,28m/s LOP Max = 80,7 dB(C) LW = 79,8/0.0 dB(A) /mW(A) 720x1600x 1,15 m/s 85 mm 135 mm...
PURPOSE OF THIS MANUAL This manual is an integral part of the machine. It was produced by BATTIPAV S.R.L. to provide those authorised to work with the machine with the information required for its foreseeable lifespan. Before starting to use this machine read the safety chapter carefully.
Battipav srl Use the right tool • Don’t use low duty tools or accessories to do the job of a heavy-duty tools. Don’t use tools for purposes not intended. Dress properly • Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.
Battipav srl RECOMMENDED USE CUTTING TOOL: DIAMOND BLADE WET CUTTING CONTINUOUS CROWN: ceramic, marble, stone, single-fired ceramic LASER/SECTORS: cement, natural stones, granite, abrasive materials TURBO: cement, natural stones, granite, refractory. THE TOOL / MATERIAL TO BE CUT MATCHES ARE PURELY INDICATIVE.
Page 14
Battipav srl IN ORDER NOT TO COMPROMISE THE MACHINE STABILITY, KEEP STRICTLY TO THE FOLLOWING PROCEDURES. WITH THE AID OF A SECOND PERSON, HOLD THE MACHINE DURING THE WHEEL KIT INSTALLATION OPERATIONS. When the machine is in working position (See paragraph: Positioning): a) loosen the left leg locking pin (motor side);...
Page 15
Battipav srl current and its length. For cables up to 50 m long, a section of 4 mm2 is enough. • Before connecting the machine to the power socket, check that the power supply voltage corresponds to that shown on the plate on the machine.
Page 16
Battipav srl table level. • Arrange the piece to be cut on the working table at the desired measurement; • Start the machine and wait until cutting blade cooling water comes out, adjusting the necessary amount by means of the water on-off valve located on the blade guard, and cut;...
LOCK THE CUTTING TOOL. RESIDUAL RISK During the design phase, BATTIPAV SRL paid particular attention to the aspects that may generate risks for the safety and health of operators. In spite of this, there are still some potential risks, which are described below: Danger of presence of electric current: The machine has an internal electric system.
• Use of non-original spare parts. EC DECLARATION OF CONFORMITY BATTIPAV SRL (Z.I.” Via Cavatorta 6/1-48033 Cotignola (RA) ITALY tel. 054540696 - info@battipav.com - www.battipav.com) hereby declares under its sole responsibility that the PRIME / SUPREME product: Series: PRIME/SUPREME Art: TAB 1 Model: Cutters for cutting on bricks, natural stones, granite, bricks, concrete products and the like up to a height of 180mm.
Page 19
MANUALENS FORMÅL Denne manual er en integreret del af maskinen. Den er udarbejdet af BATTIPAV SRL for at give de nødvendige oplysninger til dem, der er autoriseret til brug af maskinen i dens beregnede levetid. Læs omhyggeligt kapitlet vedrørende sikkerhed før brug af maskinen.
Battipav srl • Følg angivelserne vedrørende service og instruktionerne for smøring og udskiftning af dele. Undersøg ledningen med jævne mellemrum, og få den repareret hos en fagmand, hvis den er beskadiget. Undersøg ligeledes forlængerledningen med jævne mellemrum og udskift den, hvis den er beskadiget. Hold håndtagene tørre, rene og frie for olie og fedt.
Page 21
Battipav srl PRODUCENT- OG MASKINIDENTIFIKATION Det viste identifikationsskilt er påsat maskinen. Skiltet indeholder alle nødvendige referencer og forskrifter for driftssikkerheden. Bilmodel IP-klasse Artikel Produktionsår Badge nummer Maks. Værktøjsdiameter Badge nummer Værktøjets indvendige diameter Netværksfrekvens Tilbehør Nuværende forbrug Tilbehør Installeret elektrisk strøm Producentidentifikation Værktøjets rotationshastighed...
Page 22
Battipav srl STØT MASKINEN UNDER BLOKERINGEN. d) Gentag proceduren for den modsatte side. e) Løsn grebet til blokering af vognen, der sidder på glidebjælken. f) Tilslut vandrøret på vandafspærringsventilen. g) Sæt rørets støttestang i lejet. KONTROL FØR BRUG PRIME ER PROJEKTERET TIL KUN AT ARBEJDE MED VAND.
Page 23
Battipav srl Projekterer skæringslinjen på bordet. Den aktiveres, når maskinen er tilsluttet nettet. UDFØRELSE AF PLAN SKÆRING INDEN SKÆRINGEN PÅBEGYNDES, SKAL OPERATØREN SØRGE FOR, AT DER ER EN SIKKERHEDSAFSTAND PÅ MINDST 150 CM OMKRING MASKINEN. AF SIKKERHEDSGRUNDE MÅ ANDRE PERSONER IKKE OPHOLDE SIG I NÆRHEDEN AF MASKINEN UNDER SKÆRINGEN.
Page 24
ER MEGET FØLSOMT. ØVRIGE RISICI La BATTIPAV SRL har under projekteringen været særlig opmærksom på de aspekter, som kan medføre risici for operatørernes sikkerhed og helbred. På trods heraf er der stadig visse potentielle risici, som beskrives i det følgende: Fare for forekomst af elektrisk strøm:...
Page 25
Uautoriserede indgreb, der udføres af uautoriseret personale. Brug af ikke-originale reservedele. OVERENSSTEMMELSESERKLÆRING BATTIPAV SRL (Z.I. “Via Cavatorta 6 / 1-48033 Cotignola (RA) ITALIEN tlf. 054540696 - info@battipav.com - www.battipav.com) Erklærer på eget ansvar, at produktet: Serie: PRIME / SUPREME Varemodel: specificeret i TABEL 1 Type: Byggepladsskærer til skæring af mursten, natursten, granit, mursten, betonprodukter og lignende op til en højde på...
Need help?
Do you have a question about the SUPREME Series and is the answer not in the manual?
Questions and answers