Table of Contents
Advertisement
4.3 VIDEO COLOR TEMPERATURE ADJUSTMENT
(STD)
Preparation
(1) Same as "Video Color Temperature adjustment:
(HIGH)".
Adjustment
(1) Perform the following adjustment with the remote
control.
(2) Set the LCD color analyzer (CA-210) at the center of
the panel.
(3) Set color temperature to "STD".
(4) Ensure that Adjustment R/G/B DRIVE (STD) are all
set as 100.
(5) After receiving White raster signal, step down the two
(or one) among Adjustment R/G/B DRIVE (STD) and
adjust the value shown below.
Specification
Video Color temperature (STD)
x = 0.314 ± 0.005
y = 0.327 ± 0.005
(Color temp: 6500K )
At least one of the data should be 100.
Remarks
(1) Color temperature should be adjusted under the
condition in which the screen is the brightest, thus
the initial value for adjustment is set to its maximum.
(2) Adjustment is made by reducing brightness only.
Reduce a bright color for adjustment.
(3) Video color temperature & Adjustment No. are the
same, but addresses in the memory are different,
thus there's no problem.
4.4 VIDEO COLOR TEMPERATURE ADJUSTMENT
(B/W)
Preparation
(1) Same as "Video Color Temperature adjustment:
(HIGH)".
Adjustment
(1) Perform the following adjustment with the remote
control.
(2) Set the LCD color analyzer (CA-210) at the center of
the panel.
(3) Ensure that Adjustment R/G/B DRIVE (B/W) are all
set as 100.
(4) After receiving White Raster signal, step down the
two (or one) among Adjustment R/G/B DRIVE (B/W)
and adjust the value shown below.
Specification
Video Color temperature (B/W)
x = 0.335 ± 0.005
y = 0.343 ± 0.005
(Color temp: 5400K )
At least one of the data should be 100.
BACK TO ADJUSTMENTS
Remarks
(1) Color temperature should be adjusted under the
condition in which the screen is the brightest, thus
the initial value for adjustment is set to its maximum.
(2) Adjustment is made by reducing brightness only.
Reduce a bright color for adjustment.
(3) Video color temperature & Adjustment No. are the
same, but addresses in the memory are different,
thus there's no problem.
5.
DIGITAL MAIN CHECK
5.1
SYSTEM SOFTWARE VERSION CHECK
(1) Press Menu button on the R/C or control
panel.
(2) Enter the SETUP options, and then look
for UPGRADES option.
(3) The Main software version will be display
Vxxx.xxxx as shown on Fig. 1.
(4) If this version needs to be change for a
design improvement or failure, please
select the Upgrade Now button.
Fig. 1
OR
Pl ease Insert MMC card
ove
(5) The upgrading process begin by filling a
bar, when finish the message will say,
"Upgrade complete ..." when this appear
unplug the TV from the AC line outlet to
complete the process.
(6) Now plug again the TV and verify the
new software version.
(7) The Main software version will display the
latest version issue by design.
NOTE:
(1) A Service Bulletin will be sent when a
new version is issued officially to the
Service Department every time the soft-
ware version needs to be modified.
(2) In case that the upgrade fails or when a
CARD is inserted with new version and
can't upgrade ; please perform the
FACTORY RESET process to the TV,
then try upgrading again.
42
DW2U
Software Version
Setup
Reset The Software
Software Version # : Main Vxxxx.xxxx
MMC Software Upgrade
Upgrade Now
Please Insert MMC card before upgrading.
Reset TV Settings
No
Yes
(Select "Yes" to return all settings to the factory
default after main power OFF/ON.)
Move
Return
Return
SEL
Advertisement
Chapters
Table of Contents
