Related Manuals for Ferno iNSLINE Fastening System
Summary of Contents for Ferno iNSLINE Fastening System
- Page 1 iN∫LINE® Fastening System Read and Retain for Future Reference Users’ Manual October 2022 Pub. No. 234-3621-02...
-
Page 2: Ferno Customer Relations
1.937.382.1191 Internet www.ferno.com ALL OTHER LOCATIONS For assistance or information, please contact your Ferno distributor. If you do not have a Ferno distributor, please contact Ferno Serial Number___________________________ Customer Relations: Location: End of fastening system. Ferno-Washington, Inc., 70 Weil Way Wilmington, Ohio 45177-9371, U.S.A. -
Page 3: Table Of Contents
Worldwide ____________________________________ 17 Fastening-Post Retainer _________________________ 10 Accessories ___________________________________ 17 Training Record_______________________________________ 18 Fastening-Post Lock ____________________________ 10 Maintenance Record __________________________________ 19 Integrated Charging System (ICS®) ________________ 10 Floor Lock Indicator Window _____________________ 10 © Ferno / 234-3621-02 / October 2022... -
Page 4: Safety Information
The symbols defined here are used on the fastening system and/or not avoided, could result in injury or death. in this’ manual. Ferno uses symbols recognized by the International Standards Organization (ISO), American National Standards Institute (ANSI) and the emergency medical services industry. -
Page 5: Compliance
1.6 Compliance SPECIFICATIONS AND STANDARDS When properly installed and used with appropriate additional Ferno products, the iN∫LINE® fastening system meets or exceeds the following global specifications and standards. U.S.A. AMD: Ambulance Manufacturer’s Division (AMD) of the ● National Truck Equipment Association Standard 004, Litter Retention System Static Test. -
Page 6: Installation Requirements
● If the ambulance is involved in a traffic accident, inspect the fastening system. Replace any damaged components and inform Ferno. See ”Adverse Event Notice” on page 2. For complete installation information, refer to the iN∫LINE ● installation manual. See “Ferno Customer Relations” on page 2. -
Page 7: Operator Focus
The ICS delivers charging power to the iN∫X when powered and with an iN∫X secured in the fastening system. Nose: The nose is the end of the fastening system nearest the ● rear ambulance doors (or furthest from the ambulance driver.) © Ferno / 234-3621-02 / October 2022... -
Page 8: About The Fastening System
3 - ABOUT THE FASTENING SYSTEM 3.1 Description WARNING The Ferno® iN∫LINE® Fastening System is a device designed to Improper use can cause injury. Use the fastening system secure a compatible Ferno ambulance cot inside a ground-based only for the purpose described in this manual. -
Page 9: General Specifications
32.7 kg ICS Contacts Floor Lock Indicator General specifications are rounded. Metric conversions are Floor Lock Set Screw calculated before rounding. Ferno reserves the right to change Floor Lock Bolt specifications without notice. © Ferno / 234-3621-02 / October 2022... -
Page 10: Features
If any portion of green is visible, the Not Locked to Floor Locked to Floor fastener is not properly secured. The upper fastener is removable from the floor for cleaning. See the instructions on page 14 and page 15. © Ferno / 234-3621-02 / October 2022... -
Page 11: Using The Fastening System
Appropriate skills and An improper cot can cause injury. Use only a compatible training are also required. See “Operator Focus” on page 7. Ferno cot designed for use with the fastening system. ● Confirm that the fastening system operates properly and is securely locked to the floor. -
Page 12: Maintenance
• Inspecting (this page) Wipe all surfaces with disinfectant. Follow the disinfectant manufacturer’s instructions for application method and contact time. Ferno recommends you inspect the fastening system for damage as you disinfect. NOTICE Disinfectants and cleaners containing bleach, phenolics, or iodines can cause damage. -
Page 13: Lubrication-Free Fastening System
● Set the nozzle pressure at or below 3000 psi (20,684 kPa). Ferno recommends you use a nozzle with a wide angle of spray (25° or 40°). Keep the nozzle at least 18 inches (457 mm) away from the fastening system at all times. Do not spray Ingress Protection Rating directly into the ICS contacts. -
Page 14: Removing The Fastening System From The Floor For Cleaning
(U) are loose. Keep pins in place while cleaning. ○ If power-washing with the upper fastening system removed, cover both ends of the ICS connector cables with a plastic bag, held closed by a rubber band. T (2x) T (2x) © Ferno / 234-3621-02 / October 2022... -
Page 15: Attaching The Fastening System To The Ambulance Floor
Verify the upper fastening system (R) is properly positioned on the mounting rail, with the safety hook passing through the slot in the nose. The upper fastening system should fully contact the floor. S (3x) © Ferno / 234-3621-02 / October 2022... - Page 16 Allow threadlocker to dry for a minimum of one hour before use. Full cure time is 24 hours. 10. Use a 4 mm hex wrench to attach the two nose screws (O) and washers (P, Figure 16). Tighten until snug. Do not overtighten. © Ferno / 234-3621-02 / October 2022...
-
Page 17: Parts And Service, Accessories
Always follow the instructions packed with accessories. Keep the instructions with this manual. Ferno also offers a full line of emergency products for the EMS professional. Contact Ferno or your Ferno distributor for product information. See “Ferno Customer Relations” on page 2. -
Page 18: Training Record
TRAINING RECORD Training Method Trainer Date Printed Name Signature Initials Read Video/ Hands-On Manual Online © Ferno / 234-3621-02 / October 2022... -
Page 19: Maintenance Record
MAINTENANCE RECORD Date Maintenance Performed © Ferno / 234-3621-02 / October 2022... - Page 20 Aviation 11 Johnstone Road, Brendale, QLD 4500 Queensland, Australia Military Mortuary Rescue © Ferno | 234-3621-02 | October 2022...