Pro-Craft PJ25S Manual page 10

— angle 45°
Maximum cut length:
Protection category
Safety class
Dimensions:
— length
— width
— высота
Weight
LpA sound pressure level
KpA uncertainty
Sound power level
Uncertainty
Vibration (according to EN 50636-2-100) 2,5 m/s2 K = 1,5 m/s2
Description (Pic. 1)*
1. Control panel,
2. Start button,
3. Switch on/off button,
4. Base,
5. Slot desktop,
6. Miter guide,
7. Protective cover (top),
8. The screw fastening,
9. Cone widening device,
PACKAGE
The package of tile cutter includes:
◊ tile cutter - 1 pc;
◊ the guide bar - 1 pc;
◊ miter guide - 1 pc;
◊ cutting disc (installed) - 1 pc;
◊ wrench cap 12mm - 1 pc;
◊ special wrench - 1 pc;
◊ pallet - 1; - fixing bolt M6x12 - 2 pcs;
◊ locking nut - 2 pcs;
◊ plates for guide fence - 2 pcs;
◊ protective cover (upper) - 1 pc;
◊ instructions for operation and maintenance in Russian - 1 pc;
◊ warranty conditions in Russian - 1 pc;
◊ color box - 1 pc.
WARNING!
After a continuous operation for 15 minutes, switch off the tool can resume
operation in 5 minutes. It is recommended to work with a tool is not more
than 20 hours a week.
Remember, power is a source of increased danger!
Carefully read these instructions for use and maintenance.
GENERAL INFORMATION
Tile cutting machine (hereinafter referred to as "Tile cutter") is designed
for cutting ceramic tiles and porcelain tiles in household conditions.
Tile cutter is designed for use in areas with a temperate climate in
environments with temperatures ranging from 478 to + 35 ° 8, relative
humidity less than 80% and the absence of direct exposure to precipitation
and excessive dust in the air.
This manual contains information and requirements are necessary and
sufficient for reliable, safe and efficient use tile cutter.
18 mm
unlimited
IPX0
I
415 mm
395 mm
247 mm
11 kg
87 dB(A)
3 dB
100 dB(A)
3 dB
10. Cutting disc,
11. Guide bar,
12. Protective cover (bottom),
13. Pallet,
14. Rubber support,
15. The locking bolt,
16. The scale of the inclination,
17. fixing bolt.
GENERAL SAFETY RULES
Before working with tile cutter make sure that:
◊ The parameters of the supply network, working conditions and the
state of tile cutter comply with these instructions;
◊ The switch is in the "OFF";
◊ The power cord and plug are intact.
◊ When operating tile cutter IT IS PROHIBITED:
◊ Use the tool with characteristics different from the established these
instructions, as well as having mechanical damage and defects;
◊ Overload tile cutter cutter, applying excessive force to the working
tool during operation, as this leads to jamming and overheating of
the motor and, consequently, its premature failure;
◊ Ground the mechanical parts of the machine;
◊ Pull / twist / subjected to a load power cord (do not let cord contact
shell with hot and oily surfaces);
◊ Leave without supervision tile cutter connected to the power supply
mains;
◊ Perform tile cutter work while you feel tired;
◊ Allow to work with Tile cutter children and those without experience
to use it.
PROHIBITED to operate tile cutter:
◊ In areas with potentially explosive and corrosive environment is
dangerous effects on the details tile cutter;
◊ In the open air under the impact of drops and sprays (including in the
rain and snow) and dusty ambient air;
◊ Having a damaged cord or plug, and extension cords;
◊ When there is a faulty switch or a fuzzy operation;
◊ The formation of a circular fire on the surface of the reservoir;
◊ If it emits smoke or smell burning insulation;
◊ In case of high noise or vibration tile cutter;
◊ The appearance of cracks, chips on the surface of housing parts and
handles;
◊ Persons under the influence of alcohol or drugs psychotropic action;
◊ Persons under 18 years of age.
In the area of work should not be strangers (especially children) and pets.
ADDITIONAL SAFETY AT WORK.
◊ Keep hands away from cutting area and the circle.
◊ Do not touch moving parts during operation. Do not stop the disc
forcibly hands or other objects. Allow him to stay natural.
◊ Get the job done correctly in order to reduce the risk of injury, blade
binding, or loss of control.
◊ During cutting, always use the slide bar or rail line. This increases the
accuracy of cut and reduces the risk of jamming the disc.
◊ Do not attempt to free jammed disk without disabling tile cutter from
the network.
◊ Use only the appropriate discs.
◊ Never use cracked or bent discs.
◊ Do not use discs from high-speed tool steel.
◊ If you want to interrupt your work with the tool, make sure the current
process is finished, and turn off the tile cutter before distraction.
◊ Rags, clothing, wires, ropes and the like should not be left around
the workplace. Never remove the trash manually, located near the
instrument.
◊ Do not store materials and equipment of the tool, as they may fall
on him.
◊ Periodically check the tightness of all nuts, bolts and other fasteners.
◊ Never use the tool near flammable liquids or gases.
Disable tile cutter from the power supply in case of need:
◊ Preparation for work and maintenance;
◊ Moving it to a new working place;
◊ A long break or the end of the work;
◊ Replacement of the instrument parts;
◊ Tile cutter sudden stop due to interruption of the power voltage,
blade binding, or other disruptions;
EN | ENGLISH
10