Advertisement

Quick Links

0584
D
GB
F
NL
I
TR
CZ
PL
RUS
H
Operating instructions
Actuator IC 50
Contents
Contents
Actuator IC 50. . . . . . . . . . . . . . . . . . . . . . . . . . 
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
Checking the usage . . . . . . . . . . . . . . . . . . . . . 
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Part designations . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
IC 50..E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . 6
IC 50..E, continuous control: adapting the
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adapter set IC 50 for BVA/BVG . . . . . . . . . . . . . 7
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ambient conditions . . . . . . . . . . . . . . . . . . . . . . 8
Mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Logistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
E
DK
S
N
P
GR
www.docuthek.com
 
Safety
Safety
Please read and keep in a safe place
Please read through these instructions
carefully before installing or operating. Following the
installation, pass the instructions on to the opera-
tor. This unit must be installed and commissioned
in accordance with the regulations and standards
in force. These instructions can also be found at
www.docuthek.com.
Explanation of symbols
• ,  ,  ,  ... = Action
= Instruction
Liability
We will not be held liable for damage resulting from
non-observance of the instructions and non-com-
pliant use.
Safety instructions
Information that is relevant for safety is indicated in
the instructions as follows:
DANGER
Indicates potentially fatal situations.
WARNING
Indicates possible danger to life and limb.
CAUTION
Indicates possible material damage.
All interventions may only be carried out by qualified
gas technicians. Electrical interventions may only be
carried out by qualified electricians.
Conversion, spare parts
All technical changes are prohibited. Only use OEM
spare parts.
Changes to edition 0.8
The following chapters have been changed:
-
Checking the usage
-
Installation
-
Accessories
-
Certification
GB-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IC 50 and is the answer not in the manual?

Questions and answers

Summary of Contents for Krom Schroder IC 50

  • Page 1: Table Of Contents

    IC 50 ....... . . 4 Conversion, spare parts IC 50..E .
  • Page 2: Checking The Usage

    (IC 50 to the side of the pipe) Torque:  3 Nm IC 50 on butterfly valves BVA/BVG 7 Nm For the assembly of BVA/BVG and IC 50, an adapter 5 15 Nm set can be supplied, see page 2 (Installation) 0 20 Nm 0...
  • Page 3 ▷ Do not insulate the actuator with thermal insu- Wiring lation. WARNING Installing IC 50 onto butterfly valve DKR ▷ For the assembly of actuator with butterfly valve Electric shocks can be fatal! and attachment sets, and for installation in a pipe, –...
  • Page 4 IC 50 L1 L1 L1 N 7 Set switch S10 to Automatic mode. Feedback ▷ Voltage is applied to terminals 3 and 4. ▷ A feedback potentiometer offers the option of monitoring the current position of the actuator. Three-point step control ▷...
  • Page 5: Input Signal

    (OPEN) are controlled via terminals 1 and 2. Feedback Two-point step control ▷ Terminals 19 and 20: the IC 50..E offers the op- 8 Connect bridge between terminals 1 and 3. tion of monitoring the current position of the ac- tuator via the continuous 4 – 20 mA output signal.
  • Page 6: Commissioning

    (factory setting): Minimum input signal = ^ minimum angle. S3 = maximum angle, S4 = minimum angle. ▷ The IC 50..E is in Manual mode and the blue LED is lit. S3 = minimum angle, S4 = maximum angle.
  • Page 7: Changing The Direction Of Rotation

    Assembly, see page 2 (Installation). ▷ The direction of rotation is defined using DIP switch 7 and slide switch S12. Maintenance Actuators IC 50 suffer little wear and require little ser- vicing. We recommend a function check once a year. Assistance in the event of malfunction IC 50, IC 50..E...
  • Page 8: Technical Data

    ? Is it not possible for the fault to be eliminated Switching Switching cycles with the measures described above? = 0.3 current φ φ ! IC 50..E: internal error. The red LED lights up, 1 mA 1,000,000 – the blue LED flashes 2×. 22 mA – 1,000,000 •...
  • Page 9: Logistics

    Certification minimum pulse duration: 100 ms, Declaration of conformity minimum pause between 2 pulses: 100 ms. IC 50 Power consumption: 16 VA at 60 Hz, 13 VA at 50 Hz. Resistance of the feedback potentiometer: 1 kΩ, We, the manufacturer, hereby declare that the prod- max.
  • Page 10: Contact

    Contact Contact If you have any technical questions, please contact your local branch office/agent. The addresses are Elster GmbH available on the Internet or from Elster GmbH. Strotheweg 1, D-49504 Lotte (Büren) Tel. +49 541 1214-0 We reserve the right to make technical modifications Fax +49 541 1214-370 in the interests of progress.

Table of Contents