Balluff U-626-069-1X1-06-S3X Installation Manual

BF-IDU07
BIS U-626-069-1X1-06-S3X
Ultra High Frequency Passive Radio Frequency,
Identification Processor
INSTALLATION GUIDE
This document provides instructions and information
designed to assist users in the hardware setup of the BIS U-
626-069-1x1-06-S3x Processor . For configuration details
see the BIS U-62_ Processor Manual.
PACKAGE CONTENTS
Qty Description
1 BIS U-626-069-1x1-06-S3x Processor
1 UHF Series Configuration Tag
1 This Installation Guide
1 BCC06ZF Power Connector
TECHNICAL DATA
ELECTRICAL FEATURES
19.2...28.8 V DC
Power Supply
DC Input Current 1 A
Communication Interface Industrial Ethernet,
TCP/IP, MODBUS TCP
Baud Rate 10/100 Mbps
RADIO FEATURES EU US
Frequency (MHz)
ETSI EN 302 208 865...868 -
FCC part 15.247 - 902...928
Number of Channels 4 fixed 50 hopping
Frequency Tolerance ± 10 ppm over entire temp
range
Air Interface EPC C1G2
Conducted Output Power 500 mW (27 dBm) max
Antenna Connector Reverse TNC
ENVIRONMENTAL FEATURES
Operating Temperature -20...+50 °C
(-4...+122 °F)
Storage Temperature -20...+70 °C
(-4...+158 °F)
Humidity max. 90% non condensing
Vibration Resistance 14 mm @ 2...10 Hz;
EN 60068-2-6 1.5 mm @ 13...55 Hz;
2 g @ 70...200 Hz;
2 hours on each axis
Shock Resistance 30 g; 11 ms;
EN 60068-2-27 3 shocks on each axis
Protection Class
IP65
EN 60529
PHYSICAL FEATURES
Dimensions 164 x 112 x 48 mm
(6.46 x 4.41 x 1.88 in)
Weight 560 g (19.8 oz)
Enclosure Powder Coated Aluminum
USER INTERFACE
LED Indicators READY, RF, COM,
DEFAULT IP, CUSTOM IP
* When all connectors and antenna are correctly installed.
The BIS U-626-069-1x1-06-S3x Processor and its
antenna are intended for indoor use only
GENERAL VIEW
CONNECTIVITY
M12 4-pin D-Coded Female Connector (for Ethernet)
PIN 4:
RX-
PIN 1:
TX+
PIN 3:
TX-
PIN 2:
RX+
M12 5-pin Male Connector (for Power Supply)
PIN 4:
PIN 5:
N/C
N/C
PIN 3:
GND
PIN 1:
N/C
PIN 2:
VDC
DIGITAL I/O (-12 MODELS)
M12 8-pin Female Connector (Digital I/O)
This connector is available on models
BIS U-620-067-1x1-04-S32.
See the BIS U-62_ Processor Manual for details.
LED INDICATORS
The READY LED is ON after the power
READY
up sequence has completed.
green
The RF LED illuminates when RF
RF power is being transmitted by the
amber
antenna.
The
flashes ON and OFF when data is
being transmitted between the antenna
and a tag.
COM
When in Continuous Read mode, the
amber
COM LED will remain ON and will turn
OFF briefly only while data is being
read from or written to a tag.
Default IP Address enabled
DEFAULT
amber
CUSTOM User assigned IP Address enabled
amber
Typical Layout
BIS U-30x... antenna
BCC06ZF
Vdc
GND
BCC0CT1
Hub
See the BIS U-62_ Processor Manual for a complete list of accessories including
alternative cables and connectors.
DIMENSIONS
*
*
INSTALLATION GUIDELINES
•
RF performance and read/write range can be negatively
impacted by the proximity of metallic objects and liquids.
Avoid mounting the BIS U-3x... antenna within 15 cm (6
inches) of any metallic object or wet surface.
•
Do not route cables near other unshielded cables or
near wiring carrying high voltage or high current. Cross
cables at perpendicular intersections and avoid routing
COM (communications) LED
cables near motors and solenoids.
•
Avoid mounting the Processor
(electro-magnetic interference) or near devices that
generate high ESD (electro-static discharge) levels.
Always use adequate ESD prevention measures to
dissipate potentially high voltages.
•
If electrical interference is encountered (as indicated by
a significant reduction in read/write performance),
relocate the Processor to an area free from potential
(192.168.253.110)
sources of interference.
INSTALLATION
The BIS U-626-069-1x1-06-S3x Processor is designed for
Industrial Ethernet RFID applications, where the Processor
is connected in an Industrial Ethernet or TCP/IP network via
compatible cables through a hub or directly to an Industrial
Ethernet host.
1. Select a suitable location for the BIS U-62... Processor
and BIS U-30... Antenna.
Mount the BIS U-30... Antenna (within the cable
2.
distance of the Processor) and attach the BIS U-30...
Antenna cable as described in the installation guide
included with the antenna.
to Power Supply
3. Fasten the Processor to your mounting fixture using
two M5 (#10) diameter screws (not included) and
secure them with appropriate washers and nuts.
Tighten screws to 1.7 Nm or 15 lbs per inch ± 10%.
Connect the antenna cable to the UHF Processor .
PLC
4. Connect the BCC0CT1 M12 4-pin male connector to
the M12 4-pin female interface connector on the BIS U-
626-069-1x1-06-S3x Processor. Connect the BCC0CT1
RJ45 male connector to the LAN hub/switch. If
connecting directly to the host computer you will need
to use an additional crossover cable.
5. Build a power supply cable using the BCC06ZF M12 5-
pin female connector. Use minimum 24 AWG wires for
connection to the power supply lines according to the
Vdc connector pinout. Connect the BCC06ZF M12 5-
pin female connector to the M12 5-pin male connector
on the Processor . Connect the other end of the cable
(wires or user-supplied connectors) to the power
supply.
*
6. Apply power to the Processor
connections have been made. The LEDs on the unit will
flash. The READY LED is ON after the power up
sequence has completed. Then one of the Industrial
mm
Ethernet Address LEDs will remain on either Default or
in
Custom.
To verify operations, download the Balluff Dashboard™
Configuration Tool from www.balluff.com. The Balluff
Dashboard™ Configuration Tool allows users to configure
and control their BIS U-626-069-1x1-06-S3x Processor s
* Digital I/O (-S32 models only) and send RFID commands for testing purposes.
For connection details see the BIS U-62_
Manual and the Balluff Dashboard™ Configuration Tool
Manual.
near sources of EMI
after all cable
Processor