Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Homelite HLT25SDSN
Summary of Contents for Homelite HLT25SDSN
- Page 1 HLT25SDSN...
- Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product. Subject to technical modifications.
-
Page 3: Intended Use
Original instructions | English Safety, performance, and dependability have been given ■ Clear the work area before each use. Remove all top priority in the design of your grass trimmer. objects such as rocks, broken glass, nails, wire, or string that can be thrown or become entangled in the INTENDED USE string head. -
Page 4: Grass Trimmer Safety Warnings
Remember to properly replace and tighten the Never use cutting means or attachments, which are not fuel cap. specified by HOMELITE in this manual. This includes ■ Run the engine until it stops, this will remove all fuel the use of metal multi-piece pivoting chains and flail- that could become stale and leave varnish and gum in blades. -
Page 5: Residual Risk
Original instructions | English ■ Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure the product is in a safe Beware of thrown or flying objects. Keep working condition. all bystanders, especially children and pets, at least 15 m from the operating RESIDUAL RISK area. - Page 6 Original instructions | English WARNING Use unleaded petrol intended for motor vehicle use with an octane rating of 91 Do not attempt to modify the product or create ([R+M]/2) or higher. accessories not recommended for use with the product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible Sound pressure level at idle serious personal injury.
-
Page 7: Operation
Original instructions | English the positioning hole, the booms are not locked into ■ Mix the fuel thoroughly and also each time before place. Slightly rotate from side to side until the button fuelling. is locked into place. ■ Mix in small quantities. Do not mix quantities larger than usable in a 30 day period. -
Page 8: General Maintenance
Original instructions | English NOTE: Before starting the product, make sure the trimmer When cutting, make sure the cutter head is at a slight angle is lying on a flat and bare surface. while still approximately parallel to the ground surface. In tall grass, cut from the top down to ensure the moving parts Starting a cold engine: do not get tangled with the long grass. -
Page 9: Spark Arrestor
Original instructions | English ■ Unlock the retainer clockwise as shown and remove the CHECKING THE FUEL CAP retainer and spool. ■ Remove all old cutter line, and replace with the correct WARNING replacement line. A leaking fuel cap is a fire hazard and must be replaced ■... - Page 11 1. Ignition module 8. Knob 15. Front handle 2. Choke lever 9. Air filter 16. Strap hanger 3. Fuel cap 10. Lower shaft 17. Primer bulb 4. Throttle lock 11. Grass deflector 18. Starter grip 5. Switch 12. String line 19.
- Page 12 50 : 1 / 2% (50 : 1)
- Page 14 p.16 p.17 p.23 p.15 p.22 p.25 p.20 p.27 p.28...
- Page 22 22~25 Nm...
-
Page 30: Maintenance Schedule
MAINTENANCE SCHEDULE After first Every 3 Every 6 Every year Every 25 Before month or months or months or or after 300 hours each use 20 hours of 50 hours of 100 hours of hours or operation operation operation operation Check if fastener is ■... -
Page 31: Troubleshooting
TROUBLESHOOTING Problem Possible cause Solution Engine will not start. No spark. The spark plug may be damaged. Remove it and check for dirt and cracks. Replace with a new spark plug. No fuel. Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system is blocked. -
Page 32: Product Specifications
PRODUCT SPECIFICATIONS Noise emission (in accordance with ISO 22868) A-weight emission sound pressure level at the operator's Grass trimmer position Model HLT25SDSN - Idling dB (A) 76.5 Weight - Racing dB (A) 96.9 - Without fuel, cutting - Equivalent dB (A) 93.9... - Page 36 Imported by: Techtronic Industries Australia Pty. Ltd. 31 Gilby Road, Mount Waverly, VIC 3149, Melbourne, Australia Techtronic Industries N.Z. Limited 2 Landing Drive, Mangere, Auckland, 2022 , New Zealand 960994092-01...
Need help?
Do you have a question about the HLT25SDSN and is the answer not in the manual?
Questions and answers