Table of Contents
Advertisement
FRONT PANEL FACILITIES
@) POWER
STANDBY/ON
switch/indicator
(2) SPEAKER switches/indicators
FRONT A, B:
Switches and indicates for the front speaker systems A, B.
REAR:
Switches and indicates for the rear speaker systems.
CENTER:
@) BASS control switches
Use to adjust the low-frequency level. Press the + switch to increase
low-frequency level, and the — switch to decrease it.
(4) TREBLE control switches
Use to adjust the high-frequency level. Press the + switch to increase
high-frequency level, and the — switch to decrease it.
When
both
sides
(+,
—)
of the
TREBLE
control
are
pressed
simultaneously,
the treble response
will be set to the flat (normal)
condition.
Five types of tone (bass and treble) control settings can be preset.
MEMORY:
;
Press this switch to store in memory.
SELECT:
Tone setting changes as follows when pressing this switch repeatedly:
Dee
eee
-» Memory A
Memory E~
Memory D~t-Memory
C~~ Memory 5
FLAT:
Flat tone characteristics.
LOUDNESS:
Low and high frequencies are emphasized.
Use this setting to
obtain a full-bodied sound when listening.
Presetting the acoustic memory
1. Adjust the sound quality as desired using the BASS and TREBLE
control switches.
2. Press the MEMORY
switch.
3. Press the SELECT switch and select the sign to which you wish
to assign the setting (A — E) while the indicator flashes.
¢ When
the indicator lights after flashing,
it indicates
that the
command
has been stored in memory.
If you don't select memory
positions
{A —
E) while the ACOUSTIC
indicator is flashing,
nothing will be stored in memory.
paper
rao
nome cient
eA
EARP
ON
SS Oem
e In this way, the desired tone will be preset in one of the five
acoustic memory
positions. To preset four other desired tone
settings, perform the same operations.
© To recall the memorized tone settings, press the SELECT switch
to select the desired memory position.
NOTE:
e Even if the power switch is in the
STANDBY
position, provided the
power cord is plugged into an AC wail socket, memory will not be
erased. Even if the power cord /s disconnected, memory will remain
for about 2 weeks.
° /f the memory is erased, program the presets once more.
(6) REMOTE SENSOR window
@)
Display section
@) This lights when the front and rear balance and the rear and center
volume levels are being adjusted.
During volume adjustment (8) and (€) display the level, and during
balance adjustment 'B) displays the balance.
@) This gives alphanumeric display of the component selected by the
INPUT SELECTOR.
When adjusting front and rear balance and volume or center volume,
this displays balance and volume level.
It also gives alphanumeric display of SLEEP when the sleep timer is
operating, and alphanumeric display of TEST when the DOLBY PRO
LOGIC SURROUND
tone is ON.
©) This lights when the VIDEO ADAPTOR
switch is ON.
(D) This lights when the TAPE 2/DAT 2 monitor is ON.
(E) Displays the SOUND
FIELD MEMORY
selection.
During center or rear volume level adjustment, the volume level is
displayed.
The time
remaining
when
the SLEEP
TIMER
is operating
is also
displayed.
(F) In any mode other than DOLBY
PRO LOGIC
SURROUND,
if the
CENTER MONO
OUT switch is pressed, this lights.
@) Displays the DOLBY
PRO LOGIC CENTER
MODE.
(H) Displays the TREBLE and BASS adjustment settings.
(D Displays the selected ACOUSTIC MEMORY.
(J) Lights when the VCR MONO switch is ON.
'K) Displays the currently selected video signal.
It also displays the video functions. If the VIDEO SELECT switch is
pressed it changes.
(Lb) Displays the component selected by the VCR
1 RECORDING
SELECTOR
(A component that can record to VCR
1).
M) Lights when the VCR NOISE FILTER switch is ON.
(N) Displays the selected DELAY TIME.
(8) SURROUND
MODE
switches/indicators
Select the source to be used when employing the SURROUND function.
OFF:
To cancel the surround function.
STUDIO:
Enjoy the atmosphere of listening to music in a recording studio.
STADIUM:
Ideal for sports broadcasts, etc.
SIMULATED
SURROUND:
Gives concert-hall presence to monaural sound (AM, TV, etc.).
DOLBY PRO LOGIC SURROUND:
Select this setting when watching video tapes or video discs bearing
the 9
[DOLBY SURROUND] mark.
7
<ARB1177>
Advertisement
Table of Contents
