Layout; Start Up - Scheppach SBT-80 Translation Of Original Instruction Manual

m WARNING!
The product and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!
9.

Layout

m Attention! Always make sure the product is fully
assembled before commissioning!
Tools required (not included in the scope of delivery):
- 1x open-ended spanner, size 10 mm
- 1x flat nose pliers
- 1x Phillips screwdriver
9.1 Installing the handles (Fig. 3)
1. Set the pressure vessel down (5) with the front
side on a suitable surface.
2. Secure the product against slipping and toppling
(e.g. with square timbers).
3. Fit the handle (3), as shown in Fig. 2.
4. Place a washer (3b) on each of two M6x35 flat head
screws (3a) and insert them through the mounting
holes from the inside. Screw them together with
two washers (3b) and M6 hexagon nuts (3c).
Note: Do not fully tighten the screws.
5. Repeat this process for the second handle (3).
9.2 Fitting the wheels (Fig. 4, 5)
1. Insert the wheel axle (13), as shown.
2. Fit the wheels (14) provided as shown.
3. Slide wheels (14) with the washers (14b) right and
left onto the axle and secure with the split pin (14a).
4. Now tighten all the M6x35 flat head screws (3a) on
the handle (3).
9.3 Mounting the foot (Fig. 6)
1. Turn the pressure vessel (5) so that the front faces
upwards.
2. Fit the foot (10) provided as shown in.
3. Secure the stand with a split pin (10a).
9.4 Mounting the blasting hose (Fig. 7)
1. Fit the hose clamp (9a) to the blast hose (9).
2. Now push the end of the hose as far as possible
onto the blasting material discharge tube (17a).
3. Push the hose clamp (9a) over the connection
nipple and tighten it with a 10 mm open-ended
spanner.
m Attention! After mounting the blasting hose (9),
it is essential to check that it is firmly seated on the
connection nipple.
9.5 Installing the nozzle on the blasting gun (Fig. 8)
m WARNING!
Health hazard! When mounting the nozzle, there is
a risk of crushing fingers and hands.
1. To fit the correct nozzle (7), hold down the lever (6)
and open the screw fitting by turning it anti-clock-
wise. Attention! Danger of crushing!
2. Remove the sealing ring (7a) and the nozzle (7)
and store them safely.
3. Select one of the available nozzles (7) as required
and insert it with the sealing ring (7a) into the
screw connection.
4. Hold the lever (6) down again and screw the nozzle
(7) onto the blasting gun (8).

10. Start up

m Attention!
Always make sure the product is fully assembled
before commissioning!
• Systematically check the condition of nozzles,
valves and hoses before each use. The abrasive
material causes wear on the hose walls.
m WARNING!
Health hazard!
Inhalation of vapours and dusts can cause serious
damage to health, unconsciousness and in extreme
cases death.
- Do not breathe in vapours or dusts.
- Operate the product outdoors only.
10.1 Selecting the right nozzle
Select the appropriate nozzle depending on the size
(diameter) of the material.
1. To mount the nozzle (7) on the blasting gun (8),
proceed as described in 9.6.
10.2 Selecting the right blasting media
Use material with the following grain size in the prod-
uct: 0.15 - 0.25 mm. The following abrasive materials
are permissible:
• Glass beads
• Silicon carbide
• Aluminium oxide
www.scheppach.com GB | 27