Advertisement
Table of Contents
SS-1920
ITEM NO.:
SPECIFICATION:
▉ Fluid orifice ....口 1.0mm 口 1.2mm 口 1.4mm 口 1.6mm 口 1.8mm 口 2.0mm
▉ Working Pressure..................................... . 30 – 45psi
▉ Pattern...................................................... 330mm ~ 370mm
▉ Fluid Inlet ................................................. 3/8" NPS
▉ Air Consumption .......................................290 L/min
▉ Air Inlet.................................................... 1/4" NPS
1. Adjust operation air pressure from 3 to 4 bar (43 to 57psi)
Note:
Valve orifice inside three-way solenoid valve should be minimum Φ4mm(0.157") and also
operating air hose length should be within 10m(32.8ft) with the inner diameter more than
Φ6mm (0.236") to avoid delayed operation and any kind of failure.
2. Operating pressure: 43 to 57psi
3. Spray distance 150~200mm (5.9 to 7.9")
OPERATION INSTRUCTIONS
=== HOW TO OPERATE ===
1
Advertisement
Table of Contents
Related Manuals for Sumake SS-1920
Summary of Contents for Sumake SS-1920
- Page 1 OPERATION INSTRUCTIONS SS-1920 ITEM NO.: SPECIFICATION: ▉ Fluid orifice ….口 1.0mm 口 1.2mm 口 1.4mm 口 1.6mm 口 1.8mm 口 2.0mm ▉ Working Pressure………………………………. . 30 – 45psi ▉ Pattern…..…………………………………………. 330mm ~ 370mm ▉ Fluid Inlet …………………………………………. 3/8” NPS ▉ Air Consumption …………………………………290 L/min ▉...
-
Page 2: Installation
=== MAINTENANCE AFTER PAINTING === SAFETY — Turn off air and coating materials to the gun and release pressure by supplying only operating air pressure before disassembling, cleaning or servicing — Do not disassemble without receiving enough knowledge and education Pour remaining paint into another container and then clean paint passages and air cap. -
Page 3: Troubleshooting
Needle packing set- *Wear Needle set Packing seat *Insufficient tightening Paint does not flow Tip of gun Fluid adj. knob *Insufficient opening Tip hole of nozzle *Clogged Paint filter *Clogged P1: Retighten P2: Adjust P3: Clean P4: Replace parts SS-1920-I-1909A-JE... -
Page 4: Parts List
SS-1920 AUTO AIR SPRAY GUN (LOW PRESSURE) PARTS LIST Parts No. Description Q'ty Parts No. Description Q'ty SS1920-01A Air Cap Set -1.0 SS1920-10 O-Ring SS1920-01B Air Cap Set -1.2 SS1920-11 Piston Packing SS1920-01C Air Cap Set -1.4 SS1920-12 Piston SS1920-01D Air Cap Set -1.6... -
Page 5: Spray Gun
SPRAY GUN Original instructions SUMAKE Industrial Co. Ltd. - Page 6 The tool has been manufactured in conformity with the instruction of EU machine directive. The EU mark will be considered void in the event of inexpert repairs, the use of non-original parts and in case of non-observance of the safety instructions in the user’s manual. Possible direct or indirect consequential damages are not the responsibility of SUMAKE Industrial co., Ltd. General safety rules: Watch the tool at all times when in use.
- Page 7 Safety precautions for repetitive motions hazards 1. When using the tool, the operator may experience discomfort in the hands, arms, shoulders, neck, or other parts of the body. 2. While using the tool, the operator should adopt a comfortable posture. Maintain secure footing and avoid awkward or off-balanced postures.
- Page 8 General preparation and connection: Before connecting the air hose, apply 4 to 5 drops of SAE#10-20 spindle oil at the air inlet. Also, every 3 to 4 hours of operation, oiling is necessary. Twist Teflon thread tape to ensure a proper seal air inlet. Then tighten the air coupler into air tool. The supplied compressed air must be clean and dry, with the appropriate oil mist.
Need help?
Do you have a question about the SS-1920 and is the answer not in the manual?
Questions and answers