Table of Contents
Advertisement
Quick Links
SS-1182P
AIR TEXTURE HOPPER SPRAY GUN (PLASTIC CAP)
SS-1182PR
AIR TEXTURE HOPPER SPRAY GUN W/ REGULATOR (PLASTIC CAP)
PARTS LIST
No.
Parts No.
1
1182A-01
Retaining Ring
2A
1182A-02A
4.0mm Nozzle Fluid
2B
1182A-02B
6.0mm Nozzle Fluid
2C
1182A-02C
8.0mm Nozzle Fluid
3
1182A-03
Gun Body
4
1182A-04
Nut Guide
6
1182A-06
Gun Needle (Standard)
7
1182A-07
O-Ring (Φ10.82x1.78t)
8
1182A-08
Fluid Control Knob Assembly
8A
1182A-08A
O-Ring (Φ10.82x1.78t)
8B
1182A-08B
Fluid Control Knob Body
8C
1182A-08C
Washer
8D
1182A-08D
Spring
8E
1182A-08E
Screw
Description
Q'ty
No.
Parts No.
1
9
1182A-09
1
10
1182A-10
1
11A
1182A-11A
1
12
1182A-12
1
13
1182A-13
1
14
1182A-14
1
15
1182A-15
2
16
1182A-16
1
17
1182A-17
2
18
1182A-18
1
19
1182A-19
1
20
1182P-20
1
21
1182A-21
1
22
1182P-22
Description
Cage
O-Ring (Φ9.25x1.78t)
O-Ring (Φ11.5x1.5t)
Air Inlet Nipple
Bail Trigger
Gun Trigger
E-Ring
Trigger Pin
Air Regulator [SS-1182PR]
Air Fitting
O-Ring (Φ35x3t)
Plastic Hopper
pp
Hopper Clip
45∘Elbow
SS-1182P(PR)-P-1908D-HW
Q'ty
1
1
1
1
1
1
2
1
1
1
3
1
2
1
Advertisement
Table of Contents
Related Manuals for Sumake SS-1182P
Summary of Contents for Sumake SS-1182P
- Page 1 SS-1182P AIR TEXTURE HOPPER SPRAY GUN (PLASTIC CAP) SS-1182PR AIR TEXTURE HOPPER SPRAY GUN W/ REGULATOR (PLASTIC CAP) PARTS LIST Parts No. Description Q'ty Parts No. Description Q'ty 1182A-01 Retaining Ring 1182A-09 Cage 1182A-02A 4.0mm Nozzle Fluid 1182A-10 O-Ring (Φ9.25x1.78t) 1182A-02B 6.0mm Nozzle Fluid...
- Page 2 B. AIR SUPPLY: The spraying SUMAKE requires a compressor the produces 7 C.F.M. (Cubic Feet per Minute) at 25PSI (Pound per Square Inch). The supply of air must be consistent or the texture will change accordingly.
- Page 3 HORIZONTAL SURFACES & OVERHED CEILINGS A. Fill the hopper 2/3 to 3/4 full with texture material. B. Start your compressor and open the shut-off valve (if used) allowing air to discharge through the hopper gun. C. Standing on the floor or other stable surface. Life the hopper gun until it is approximately 18” below and angled toward the surface at between 30 and 50 degrees at a starting point near the corner or edge.
- Page 4 C. Stand 3 to 4 feet from the surface to be textured (except horizontal surfaces). D. Lift your spraying SUMAKE toward the top of the surface to be sprayed (at a corner or edge). E. Pull the trigger and start moving your spraying SUMAKE vertically, down the surface until you are near the bottom.
- Page 5 SPRAY GUN Original instructions SUMAKE Industrial Co. Ltd.
- Page 6 The tool has been manufactured in conformity with the instruction of EU machine directive. The EU mark will be considered void in the event of inexpert repairs, the use of non-original parts and in case of non-observance of the safety instructions in the user’s manual. Possible direct or indirect consequential damages are not the responsibility of SUMAKE Industrial co., Ltd. General safety rules: Watch the tool at all times when in use.
- Page 7 Safety precautions for repetitive motions hazards 1. When using the tool, the operator may experience discomfort in the hands, arms, shoulders, neck, or other parts of the body. 2. While using the tool, the operator should adopt a comfortable posture. Maintain secure footing and avoid awkward or off-balanced postures.
- Page 8 General preparation and connection: Before connecting the air hose, apply 4 to 5 drops of SAE#10-20 spindle oil at the air inlet. Also, every 3 to 4 hours of operation, oiling is necessary. Twist Teflon thread tape to ensure a proper seal air inlet. Then tighten the air coupler into air tool. The supplied compressed air must be clean and dry, with the appropriate oil mist.
Need help?
Do you have a question about the SS-1182P and is the answer not in the manual?
Questions and answers