Table of Contents
Advertisement
@ Audio Mode Indications and Description of Operation
Audio Control
Up/Down
Buttons
Audio Mode
VOL
volume
adjustment
BASS
bass
adjustment
Ty!
TREB |
treble
adjustment
BAL
left/right
balance
adjustment
FAD
front/rear
balance
adjustment
Center Position
the steps indicated on the display do not match due to the large number of
Note 1:
In the balance and fader adjustment modes, the actual steps and
steps.
Note 2:
The original display reappears
approximately 7 seconds after the adjustments in the various audio modes.
Note 3:
The various modes are set to the following values when the power is first turned on after the set is installed in the car: VOL 13 .BAO,TRO,
BoOandF 0.
% Setting the DSP Mode
lf you have a Digital Sound Processor (DSP) connected to your unit,
you must carry out this setting without fail. Turn the volume to MAX
(Vo33). Holding down button
® press button
@3 . The adjustments of
the volume and tons are carried on the Digital Sound Processor.
* rie
3 the Equalizer Mode
If you
have an Equalizer or a Digital Sound Processor with a built-in
equalizer connected to your unit, you must carry out this setting
without fail. Holding down button
@ , press button
@ . The bass/
treble adjustment is carried out on the equalizer.
% Monitor
The tape deck continues to operate even if the mode is-switched for
example to the radio mode while fast-forwarding, rewinding or searching
on a tape.
2. Listening to the Radio
%* Tuner Mode Selection/Band Selection Button @
@
@
Tuner Mode Selection
Press button
@
to set the tuner mode.
Band
Selection
When you press button
@ , the reception band changes in the
following order:
FM1—>FM2—>FM3—>AM(L/M)—>FM1
(FM1, FM2 and FM3 are on the same reception frequency band.)
* Tuning Mode Selector Button (T-M) @
Press the button
@)
so that "MANU"
appears on the display. The
manual tuning mode is now set. Tune into a station by pressing button
Or button
@) . Unless you press button
@ _ or button @ within
7 seconds of switching to the manual tuning mode, the unit will return
to the seek tuning mode.
@
Manual Tuning
During FM reception, the frequency changes in steps of 0.05 MHz.
On MW, it changes in steps of 9 kHz, and on LW, in steps of 1 kHz.
1. Press the button
@) to set the manual tuning mode.
2. When you press button
, the frequency increases, and when
you press button
@ , it decreases.
Seek Tuning (Locai/DX)
There are two sensitivity levels for seek tuning: DX seek, which will
tune in any broadcasting stations which can be received, and Local
seek, where only those stations with a sufficiently strong signal, i. e.
local stations, can be tuned in.
<DX Seek>
1. Check that the "DX" indicator
(@) is lit. If not, press button
21
formore than 2 seconds.
2. Press button
to tune toward higher frequencies and press
button
@Q
to tune toward lower frequencies.
Tuning will stop when a broadcast station is received.
<Local Seek>
1. The "DX" indicator () appears when button @) is pressed for
over 2 seconds.
Press button
to tune toward higher frequencies and press
button
@
to tune toward lower frequencies.
Tuning will stop when a broadcast station with a strong signal
is
received.
2:
%K MUTE Button @
When button
@) is pressed, the sound turns off and "MUTE" appears.
Press the button again to cancel the muting mode.
* Preset Buttons 1, 2,3,4,5and6
@
©
By pressing a Preset button you can instantly recail a station which has
been stored in memory.
* Storing Stations in the Preset Memory
6 radio stations can be stored in memory for each band.
1. Press button
@
to select the reception band.
. Tune in the broadcasting station using Manual Tuning.
% Preset Scan/Auto Store Memory Button
@&
@
Preset Scan
1 to 6 will be received in order for 7 seconds each.
When you press button @ again, or press one of the Preset buttons
1 to 6, this mode will be released. (When the unit is receivingon
order.)
% If you press button
for more than 2 seconds, the Auto store
memory mode will become operative,
All the stations stord in
the memory so far will be cleared, and new ones will be stred
instead, so be careful.
Auto Store Memory
for each band. (See "Storing Stations in the Preset Memory'. |
* Stations previously stored in the preset memory are cleate;
when new ones are stored using Auto Store.
ARX3170V ARX3-70E
Advertisement
Table of Contents
