Tape Operations; Basic Recording; Programmed Playback - Aiwa NSX-SZ310 Operating Instructions Manual

TAPE OPERATIONS
Playback
Use only type | (normal) tapes.
71 Press TAPE and insert the tape in either deck.
Press &PUSH EJECT to open the cassette holder, and
insert with the exposed side down and playback side
facing out from the unit. Push the cassette holder to close.
&PUSH EJECT
2 Press >.
To stop playback
Press iil.
To pause playback (DECK 2 only)
Press IM. Press again to resume.
To fast forward or rewind
Press <<@ or >>.
To select a deck (DECK 1 or DECK 2)
Press TAPE in stop mode when tapes are loaded in both decks.
The deck number ("TP1" or "TP2") is displayed.
To reset the tape counter
Press MECLEAR in stop mode, and the tape counter on the
display is reset to "OOOO".
Opening and closing the cassette holder wil! also reset the
tape counter.
To play continuously (DECK 1 to DECK 2 )
Load tapes in both decks and start playback on DECK 1. Then,
as soon as playback on DECK 1 finishes, playback on DECK
2 will start without interruption.
To play back type Hi (High position) tapes
Turn MULTI JOG until "SOFT" is displayed while playing a
type II tape.
Then, the unit provides the optimum playback sound for type
Il tapes.
Notes on cassettes
© Use of 120-minute or longer tapes is not recommended
since they are extremely thin and easily deformed or
damaged.
© Take up any slack in the tape with a pencil or similar tool
before use. Slack tape may jam in the mechanism.
© "SOFT" sound for type Il tapes described above is cancelled
when the graphic equalizer is turned on, the cassette holder
is opened, the function is changed, or the unit is turned off.
Basic recording
Use only type | (normal) tapes. DECK 2 is the recording deck.
Only one side of the tape can be recorded at a time.
7 Insert the recording tape in DECK 2.
Press 4 PUSH EJECT to open the cassette holder, and
insert with the exposed side down and the side to be
recorded on facing out from the unit.
Wind up the tape to the desired point if needed.
2 Prepare the source.
To record CD{s), select the CD function and load disc(s).
To record aradio broadcast, tune in to the desired station.
To record a tape, select the tape function and insert the
source tape in DECK 1.
To record from connected external equipment, select the
VIDEO (AUX/TV) function and prepare the equipment.
3 Press @REC/REC MUTE to start recording.
When recording a CD or tape, playback starts
automatically.
When recording input from connected equipment,
manually start playback of the source.
14
Programmed playback To check the program
Plays back up to 30 selected tracks in programmed order.
7 Press SHIFT+PRGM on the remote control during
stop.
"PRGM'" lights up on the display.
2 Press DISC DIRECT PLAY 1-3 to select a disc.
Go to the next step when the tray stops rotating.
3 Press the numbered buttons on the remote
control to program a track.
The selected track number lights up on the display.
-To select the 25th track, press +10, +10 and 5.
-To select the 10th track, press +10 and 0.
4 Repeat step 2 and 3 to program other tracks.
5 Press >.
During programmed playback, you cannot select a disc or
a track with the numbered buttons. "CAN'T USE" is
displayed when you try to select a track .
elf the total playback time of the program exceeds 99:59
minutes, or ifa track with a track number exceeding 30 is
programmed, the playing time is displayed as "- -:- -".
¢You cannot program more than 30 tracks. "FULL" is
displayed.
Press << or BB repeatedly during stop. The disc number,
track number and program number are displayed in
succession.
To clear the program
Press MCLEAR during stop. "PRGM" disappears on the
display.
To add tracks to the program
Repeat step 2 and 3 before starting playback. The tracks are
added to the end of the program.
To change the programmed tracks
Clear the program and reselect the tracks in your desired order.
© Do not place more than one disc on one tray.
© Do not tilt the unit with discs loaded.
© The unit may not play a CD-R/RW disc recorded on personal
computers or certain kinds of CD-R/RW recorders.
© Do not attach adhesive label, etc. to either side of a CD-R/
RW disc, as doing so may cause malfunction.
© Do not load an unrecorded CD-R/RW disc. The disc may be
damaged.
© Do not use irregular-shaped CDs.
En
11