http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
http://www.xiaoyu163.com NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block 3 7 63 1515 0 When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed.
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 E C B E C B B C E E C B CD1585BC 2SC3331 DTC114ES 2SB1370 CSA952K KTC3199GR CSC4115BC KTA1266GR KTC3198GR S D G 2SK360E 2SJ460 2SK2158 2SA1235F CSD1306E 2SK2541 KRC102S-RTK 2SC2714 KRC104S 2SC3052F CMBT5401...
Page 22
http://www.xiaoyu163.com WIRING – 6 (DECK : ZZM-3 YPR1NM)<LH> 3 7 6 3 1 5 1 5 0 FROM B FRONT C. B CN104 D DECK C . B FC104 1 3 9 4 2 2 9 6 5 1 3 DECK MOTOR w w w...
Page 28
http://www.xiaoyu163.com IC DESCRIPTION µ PD780226GF-019-3BA 3 7 63 1515 0 Pin No. Pin Name Description O-MOTOR DECK MOTOR ON/OFF output. O-SOL1 DECK1 solenoid output. O-SOL2 DECK2 solenoid output. – Not connected. O-RVS_LED PRESET (REV) LED ON/OFF output <HS,HT only>. O-SET_LED SET LED ON/OFF output.
Page 29
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description I-CDSW CD mecha switch input. I-SPEANA_L A/D L-input for spectrum analyser level display. I-SPEANA_R A/D R-input for spectrum analyser level display. I-KEY1 Key1 input. I-KEY2 Key2 input. I-KEY3 Key3 input. I-TU_SIG Tuner signal input.
Page 30
http://www.xiaoyu163.com ADJUSTMENT <TUNER / DECK / FRONT> 3 7 63 1515 0 < TUNER SECTION > 1. Clock frequency Check 10. FM Tracking Check Settings : • Test point : TP2 (CLK) Settings : • Test point : TP8(Lch), TP9(Rch) Method : LH,HS: Set to AM 1710kHz and check that the test Method : Set to FM 98.0MHz and check that the test point is less point is 2160kHz ±...
Page 31
http://www.xiaoyu163.com 3 7 63 1515 0 < DECK SECTION > < FRONT SECTION > 18. µ-con OSC Adjustment 12. Tape Speed Adjustment (DECK 2) Settings : • Test tape : TTA–100 Settings : • Test point : TP11(KEY-SCAN), GND • Test point : TP8(Lch), TP9(Rch) •...
http://www.xiaoyu163.com TAPE MECHANISM PARTS LIST 1 / 1 <ZZM-3 YPR1NM> 3 7 63 1515 0 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 8Z-ZM3-227-010 BELT,MAIN M3 8Z-ZM3-233-010 SPR-T,BRG M3 8Z-ZM3-235-010 BELT,MAIN L 84-ZM2-227-310 SPR-C,AZIMUTH 8Z-ZM1-235-010 PULLEY,MOT 87-A90-403-110 HEAD,RPH MS15R 87-045-347-010...
Page 36
http://www.xiaoyu163.com TAPE MECHANISM EXPLODED VIEW 1 / 1 <6ZM-3 PR2NM> 3 7 6 3 1 5 1 5 0 PH (DECK 1) E/RPH (DECK 2) DECK C.B SOL 2 (DECK L only) SOL 1 (DECK L SIDE) (DECK R SIDE) LEVER EJECT R 1 3 9 4 2 2 9 6 5 1 3...
Page 37
http://www.xiaoyu163.com TAPE MECHANISM PARTS LIST 1 / 1 <6ZM-3 PR2NM> 3 7 63 1515 0 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 1 86-ZM3-215-010 CHAS ASSY,RS 41 82-ZM1-216-310 GEAR,REEL 2 86-ZM3-202-010 BASE,HEAD S 42 86-ZM3-213-010 S-SCREW,HLDR,MOT 3 3 86-ZM3-205-010 SPR-C,RPH S...
Page 38
http://www.xiaoyu163.com SPEAKER DISASSEMBLY INSTRUCTIONS 3 7 63 1515 0 Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units. 2 (() flat head screwdriver 3 Cut chisel How to Remove the PANEL, FR...