Hoover HE332ALG User Manual page 7

GETTING TO KNOW YOUR CLEANER
A. Bag Door
A1. Carry Handle
B. Bag Door Latch
C. Bag Check Indicator
D. Cord Reel Pedal
E. Hose Latch (For Nano
Pack™ system)
F. Parking Slot
G. Variable Power Rotary Control
H. On/Off Pedal
I. Exhaust Filter Cover
J. Exhaust Filter Cover Release Latch
K. 2in1 Tool
L. Hose
M. Bag Release Button
ASSEMBLING YOUR CLEANER
Remove all components from the packaging:
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position.
[1] To release the hose: simply press the two latches on the hose end and pull.
2. Connect the hose handle to the upper tube end. [2]
3. Connect the tube lower end to the Carpet and Floor Nozzle** or accessories if
required. [3]
USING YOUR CLEANER
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [6]
2. Adjust the telescopic tube to the desired height by pressing the button on the
telescopic tube adjuster and raise or lower the tube to the most comfortable cleaning
position. [5]
3. After connecting the telescopic tube to the Carpet and Floor Nozzle**, adjust the
suction control slider on the nozzle according to your cleaning needs [4]:
- Hard Floor Cleaning – Adjust the suction control slider on the nozzle to the symbol.
- Standard Carpet – Adjust the suction control slider on the nozzle to the symbol.
- Long Pile Carpet – Adjust the suction control slider on the nozzle to the symbol.
To obtain the best performance and efficiency on Carpet adjust the suction control slider
to the symbol. The suction control can also be used to reduce the operating push force.
N. Bag
O. Pre-Motor Filter
P. Pre-Motor Filter Frame
Q. Exhaust Filter
R. Hose Handle
R1. Hose Handle Hook (For Nano Pack™
system)
S. Suction Regulator
T. Telescopic Tube Adjuster
U. Telescopic Tube
V. Carpet and Floor Nozzle**
W. Suction Control Slider
X. Pet Hair Remover Mini Turbo Nozzle*
Y. Allergy Remover Mini Turbo Nozzle*
Z. Parquet Nozzle*
Switch the cleaner on by pressing the On/Off Pedal on the cleaner main body. [7]
4.
Rotate the Variable Power Rotary Control to increase or decrease the power [8] and
5.
then you can start vacuuming. [10]
Switch off at the end of use by pressing the On/Off Pedal. [7] Unplug and press the cord
6.
rewind button to wind the power cord back into the cleaner.
PARKING AND STORAGE SECTION
The flexible hose and telescopic tube can be parked temporarily while in use [11] or in the
Nano Pack™ storage position when not in use [13]:
Retract the telescopic tube to its storage length. [14]
1.
2. Remove the nozzle from the end of the telescopic tube.
3. Remove the hose handle from the telescopic tube.
4. Lift the Hose Latch at the rear of the cleaner and wrap the flexible hose around the
product. [12,13]
5. Place the nozzle into the nozzle parking slot underneath the product. [14]
6. Place the telescopic tube into the telescopic tube parking slot underneath the
product. [14]
CLEANER MAINTENANCE
Replacing the Dust Bag
If the bag check indicator is red, please check the bag and, if necessary, replace it.
Lift the bag door release latch and open the bag door. [15]
1.
Lift the handle of the bag holder up. [16]
2.
3. Hold the bag with the holder over a bin. Press the red button to automatically release
the bag without any contact with dust. [17]
Fold a new bag [18] and insert the collar into the bag holder. [19]
4.
5. Refit the bag with holder back into the appliance.
6. Close the bag door.
WARNING: The bag door will NOT close if the dust bag and/or the bag auto eject
mechanism are not assembled to the cleaner. Always ensure the bag and bag auto eject
mechanism are present when closing the bag door.
REMEMBER: The bag check indicator may be red if an obstruction has occurred. In this
case refer to 'Removing a blockage from the system'.
Cleaning the Filters:
To maintain optimum performance of your cleaner, please wash the pre-motor filter and
exhaust filter after each 5 bag changes.
Cleaning the pre-motor filter:
1. Lift the bag door latch to open the bag door and remove the holder. [15,16]
2. Slide the pre-motor filter frame from the cleaner. [20]
3. Remove the filter from the frame. [21]
2
*Certain Models Only
GB
**Nozzle design may vary according to models