Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Washtech STARLINE XU 4 Series
Summary of Contents for Washtech STARLINE XU 4 Series
- Page 1 OPERATOR MANUAL...
- Page 2 This document is subject to change without prior notice. Information supplied in this manual is copyright. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical without the express permission of Washtech. 1/8/2023...
-
Page 3: Table Of Contents
CONTENTS Warning Contents Safety Instructions Installation Diagram Installation Instructions Installation Checklist Installation Troubleshooting 10. Operator Use Guide 11. Operator Troubleshooting 12. Schematic Diagram 13. Accessories 14. Spare Parts List 15. Notes 1/8/2023 Starline XU Series-4 Operator Manual... -
Page 4: Warning
SAFETY INSTRUCTIONS INSTALLATION • Use qualified, skilled personnel. • Follow installation instructions. • Connect to correct voltage and supply current, and (if applicable for the model) check that the phase rotation is correct. • Provide fully accessible Electrical Isolation Switch & water supply valves. TRAINING AND SUPERVISION •... -
Page 5: Installation Diagram
INSTALLATION DIAGRAM XU SERIES-4 • Part #: XU4 INST • Date: 2/8/2023 • Version: SERVICES • A Hot Water 200-350kPa 3/4" • B Waste Flexihose supplied 25mm • C Electrical Connection 230V, 50Hz, 1P-N+E~ 1/8/2023 Starline XU Series-4 Operator Manual... -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS MACHINE POSITIONING • Unpack machine, check for damage and complete delivery. • Install machine on sound waterproof self-draining floor • Use the adjustable feet/legs to ensure that the machine is level. NOTE: Failure to level the machine correctly may result in leaking during the cycle, overflowing from the door sill, poor hygiene through the wash tank not being able to drain correctly, and/or visibly uneven door. - Page 7 INSTALLATION INSTRUCTIONS INLET WATER Incoming water should be within the following standard requirements: • Temperature: 65°C. NOTE: Low temperatures will increase the recovery time between cycles and depending on the chemical being used, may result in excessive foaming if the machine is started before the wash water is up to a suitable temperature.
-
Page 8: Installation Checklist
INSTALLATION CHECKLIST CHECK NOTES DELIVERY SUPPLIED COMPLETE? CHECK THERE HAS NOT BEEN ANY TRANSIT DAMAGE POSITION LEVEL AND STABLE? ON SOUND, WATERPROOF, SELF-DRAINING FLOOR WATER ISOLATOR VALVE FITTED? ACCESSIBLE, ALL FITTINGS SOUND, AND NO LEAKS TEMPERATURE CORRECT? HOT WATER INLET 65˚C PRESSURE CORRECT (200 –... -
Page 9: Installation Troubleshooting
INSTALLATION TROUBLESHOOTING DOOR NOT CLOSING PROPERLY • Level the dishwasher. MACHINE NOT STARTING OR FILLING • Ensure water supply to machine is turned on. • Ensure power supply to machine is turned on. • Check that the water inlet hose is not twisted or kinked. CYCLE TAKING TOO LONG •... -
Page 10: Operator Use Guide
OPERATOR USE GUIDE START • Turn on at wall. • Ensure the Wash / Drain Filter Basket (1) is in place and shut the door. • Press the Power switch, the switch will glow red and the machine will fill automatically. OPERATION •... -
Page 11: Operator Troubleshooting
OPERATOR TROUBLESHOOTING ISSUE CAUSE ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ DISHES NOT CLEAN ⚫ ⚫ ⚫ STAINING ⚫ ⚫ ⚫ FOAMING ⚫ PROTEIN BLOOM ⚫ ⚫ DIRTY MACHINE ... -
Page 12: Schematic Diagram
SCHEMATIC DIAGRAM XV/XU SCHEMATIC • Part #: 120130 • Date: 31/8/2022 • Version: 1/8/2023 Starline XU Series-4 Operator Manual... -
Page 13: Accessories
ACCESSORIES XU SERIES-4 • Part #: XU4 ACS • Date: 2/08/2023 • Version: 1/8/2023 Starline XU Series-4 Operator Manual... -
Page 14: Spare Parts List
SPARE PARTS DESCRIPTION PART NO CABINET & DOOR • Front Panel 288 20010 • Lower Rear Panel 288 20004 • Door 288 10006 • Door Catch Plunger Assembly 400 10104 CONTROLS & INDICATOR • Door Reed Switch 600 30183 • Drain Switch 600 30517 •... -
Page 15: Notes
NOTES 1/8/2023 Starline XU Series-4 Operator Manual... - Page 16 All Washtech products are designed and manufactured using the internationally recognised ISO9001 quality management system, covering design, manufacture and final inspection, ensuring consistently high quality.