Tape Punch; Operating Procedure; Local Mode; On-Line Lvlode - GE TermiNet 300 Operator's Manual

GEH-2184A
Operator's Manual
T .\I )E E I)ITTI\G
·r,,
l)
r1
p:1
rt'
:1
rH'\V correct tape, place the uncor-
1 · , ' ·
t ,
1
I t :
1 !
i , ·
i 11
t I
1 ( ,
t
a p
e
r
e
a
ct e
r •
F
o
11
o \V
St
f'
I )
s
1
tl11
11
11'_'!1
:~
1!!1d1'r
(Jperation, and then procet'cl '.vith
t
l
1
!
l
1
il I (
I ' . \ '
I I l ' . ' .
s tt
l
p s :
1.
S<·:111 tlii·
printed copy n1ade during the first
pun(·llir1~~
<Jf
tlH'
tape to detern1ine the areas that
ll\'1
1!
t(>
1H'
C'(ll'rt·cted.
~. 'Turn the punch and reader ON.
3. Detern1ine that the tape pw1ch has blank tape
re~icly for pw1ching·.
4. Copy punch a new tape until the incorrect
character, word, or line is reached.
:J. Stop the reader and place the RE . . . A..D-OMIT
switch in the OMIT position.
G. To correct a word, press the WORD pushbut-
ton on the reader. The word containing the error
will run through the reader, but will not be punched
on the new tape. The san1e applies to a character
or line.
7. The correct word should now be typed. It will
then appear on the corrected tape.
8. !)rc·c e cd \Vi th the new tape by turning the
reader ON*
TAPE PUNCH
Operation
Press the OFF or ON button on the front of the
punch drawer to stop or start the pW1ch.
Pushing the TAPE FEED pushbutton on the punch
drawer will produce tape feed
if
depressed while
the punch switch is ON.
To turn a ren1ote punch ON or OFF, hold down
the control key and depress the PUNCH ON (R) or
PUNCH OFF (T) key.
OPERATING PROCEDURE
CAUTION: .1LS A SAF'ETY PRECAUTI01V
I
J(
>
.V(
J
T OP Elt.11 TE Tl!E T ER AJJ1VE T 300
1 Jf~ l.\' Tl:J? H'ITJJ Tl!E C 011 ER LIFTED.
LOCAL MODE
Press the LOCAL button. The button will light
and the print belt will rotate. Set the SUPPRESS
PRINT switch in the normal position.
10
1. Local Printing - The tern1inal will print-1
)ut
when
tht~keys
are clepre ssed.
2.
Local Tape Punching - Press the Punch
ON
button~ --T~puncl1-will-
generate a tape in addition
to print-out when the keys are depressed.
3. Printing fron1 tape - Insert the punched tape
in the
--~reicle-r
anclpre-ssthe reader ON button. Tht'
tape will
~1clvance
and print-out will take place
~it
the speed
of
the rate selector S\Vitch setting on
tlli,
tern1inal.
ON-LINE MODE
Depressing the ON-LINE pushbutton will enable
the Tern1iNet 300 tern1inal to be operated ren1otely.
When in this condition, all of the functions n1e11-
tioned previously under LOC~A..L MODE can be used
tn acct.'SS ~llHltht-ir tern1inal or con1puter.
To Access a Computer
1. Set the upper-lower case switch on the back
of the bustle to the desired position.
2. Set the rate switch on the control panel to a
speed con1patible with the con1puter.
3. Set the line-feed to single or double spaci11~ 1 ,.
4. Set the auto line-feed to the OFF pos1tir"·n.
5. Set the suppress switch to nor1nal. If print-
out is not desired, the suppress switch should be in
the Suppress Print position.
6. Dial the con1puter nun1ber. When the audible
tone is heard, push the data button on the data-set,
or place the phone in the cradle on the coupler. The
READY light will come on. The terrr1inal is now
coupled with the computer.
To Disconnect a Computer
1. Use con1puter "Cut Off'' code, i.e., ''done",
"bye", etc. or hold control key and depress DLE
(P) - EOT (D). This will drop the data--line and
return the terminal to ''Standby".
To Access Another Terminal
The following steps should be followed:
1.
The suppress switch should be in
thi·
1uirnL1l
position.
2. The rate select switch setting;
n1ust 1H' tilt·
san1e as the tern1i11al lH'i11g
accesS('CI.