U-Line UONP115SS01B Quick Start Manual page 33

cleaner.
QUICK START GUIDE
Stainless Models
Stainless door panels, handles and frames can discolor
when exposed to chlorine gas, pool chemicals, saltwater or
cleaners with bleach.
9. When water begins flowing over the evaporator
Keep your stainless unit looking new by cleaning with a
(approximately 3 minutes), pour 1 packet of CLR
good quality all-in-one stainless steel cleaner and polish
cleaner into the water trough. The cleaning process will
monthly. For best results use Claire
last approximately 45 minutes.
Polish and Cleaner. Comparable products are acceptable.
Frequent cleaning will remove surface contamination that
10. Dilute 1 tablespoon bleach in 1 gallon of warm water.
could lead to rust. Some installations may require cleaning
Apply this solution to the entire inside of the storage
weekly.
area. Then rinse thoroughly with water.
Do not clean with steel wool pads.
Do not use stainless steel cleaners or polishes on
The unit will resume operation approximately 15 minutes
any glass surfaces.
after the automated cleaning process is completed. The
Clean any glass surfaces with a non-chlorine glass cleaner.
water fill valve will energize, fill the water reservoir, and
Do not use cleaners not specifically intended for
shut-off after three minutes. The compressor begins to
stainless steel on stainless steel surfaces (this
operate and water flows over the evaporator assembly (ice
includes glass, tile, and counter cleaners).
mold). Initially, the water flow may not be uniform, causing
uneven sized cubes or water to spill into the ice storage bin.
If any surface discoloring or rusting appears, clean it
This is a normal situation that will correct itself within the
quickly with Bon-Ami or Barkeepers Friend Cleanser
®
first 24 hours of operation.
a nonabrasive cloth. Always clean with the grain. Always
finish with Claire Stainless Steel Polish and Cleaner or
®
NOTICE
comparable product to prevent further problems.
Discard all ice produced in the first harvest.
Using abrasive pads such as ScotchBrite™ will
cause the graining in the stainless steel to
become blurred.
Should power to the unit be interrupted during
Rust not cleaned up promptly can penetrate the
the self-clean cycle, it will be necessary to repeat
surface of the stainless steel and complete
the complete cleaning cycle after the power is
removal of the rust may not be possible.
restored.
For information on Keg and Tap Towers, please reference
the Single and Double Tap Tower Kits User Guide on
REFRESH KIT
u-line.com.
Due to variations in water quality or inadequate
maintenance, your unit may become excessively coated in
lime scale or calcium. U-Line offers a cost effective refresh
Cleaning
kit which replaces man interior components and will return
your unit to like-new condition. Refresh kits may be ordered
from your local distributor and installed by your local
service company. For information on your local distributor
or service company please visit www.u-line.com.
Stainless Steel
®
and
®
Rinse the interior using a soft sponge and clean water.
Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transfer taste
and/or odor to the interior products and damage or discolor
the interior.
NUGGET ICE MACHINE CLEANING CYCLE
This ice machine has an automatic clean alert function.
The control will indicate
to clean your unit. When
will continue. Depending on water conditions, more
frequent cleaning may be necessary: see chart below.
Cleaning removes lime scale, other mineral deposits, and
sanitizes the machine. Poor ice quality and reduced ice
output are signs that cleaning is necessary.
CAUTION
!
BEFORE RUNNING THE CLEANING CYCLE,
MEASURE THE TDS (TOTAL DISSOLVED SOLIDS)
LEVEL OF YOUR WATER SUPPLY.
(See WATER HOOKUP section in this guide to find
instructions for using the TDS meter that was included
with this ice machine.)
TDS (Total Dissolved Solids)
(ppm)
5 - 150 ppm
150 - 200 ppm
Replacement TDS meter may be ordered at uline.com
USER GUIDE
Part # 80-55672-00
Under normal conditions cleaning should be done
when the display shows
cleaning cycle at any time by pressing and holding
the clean button for 10 seconds.
in the display indicating the start of the cleaning
process.
Failure to clean may reduce the quality and quantity of ice
produced. Once the clean cycle begins, it can be canceled
by pressing three times. Press
making ice. The clean cycle will automatically cancel if user
fails to activate control at steps 2, 3b, and 5b within 2 hours.
Required for cleaning:
• Clean potable water
• Bucket and cleaning sponge
• Internal water filter (if applicable) —
ULANUGGETFILTER**
33
• SafeCLEAN Plus™ Cleaner — ULANUGGETCLEAN**
• Hose (7⁄16" ID x 9⁄16" OD) and funnel
CL
in the display, reminding you
CL
is displayed, ice production
Cleaning Interval
6 months
4 months
CL
. You may initiate a
0 1
will appear
once more to start
1
2