Related Manuals for Delta Ecodrip Series
Summary of Contents for Delta Ecodrip Series
- Page 1 ECODRIP SERIES FILTER/DRIP SYSTEM MODELS 8115 & 8230 9125 Comar Drive, Walker, LA 70785 (800) 219-9183 Care and Operation Manual K4514 4/18 ©2018 Delta Treatment Systems, LLC...
- Page 2 National Sanitation Foundation (NSF) in accordance with NSF/ANSI Standards 40 or 245, Class 1 effluent requirements. All of the Delta Treatment Systems aerobic treatment plants are listed by NSF in accordance with ANSI/NSF Standard 40 at a minimum, Class 1 and make a perfect combination when used with the ECODRIP Filter/Drip System and drip line designed for Class 1 effluent water.
- Page 3 Check the air filter on the air compressor. Rinse with warm water life of the microorganisms inside the system. Delta is not if necessary. responsible for the in-field operation of the system, other Check the screen filter in the filter system.
- Page 4 Note: Each system is designed to be hydraulically balanced with a maximum 300 feet of supply line between the pump and the inlet to the drip field with a maximum elevation difference of 30 feet. Consult Delta Treatment Systems for alternate designs.
- Page 5 Site Slope _________% When slopes of 20% or greater are encountered use three (3) ft. minimum lateral spacing Refer to Drip Tubing Chart (Table 1) in this manual for standard Drip Tubing zones, Consult Delta Treatment Systems for optional zone sizing.
- Page 6 SIzE OF THE ABSORPTION FIELD to the emitter supply manifold should be as indicated on drawing to reduce the friction loss to a minimum and keep the velocity above 2 feet per second. Each zone must not The total size of the absorption area depends on the daily have more than indicated on Table 1.
- Page 7 FILTER SYSTEM SPECIFICATIONS MODEL 8115-1/2HP WITH GEOFLOW CLASSIC MODEL 8230-1HP WITH GEOFLOW CLASSIC ® ® Operating Perameters Operating Perameters Motor/pump size 1/2 HP (standard) Motor/pump size 1 HP (standard) Pressure at outlet of regulator 20-PSI nominal Pressure at outlet of regulator 20-PSI nominal Maximum particle size 100 microns...
-
Page 8: Installation Instructions
Attach the float switches to the discharge pipe using clamps installation or damage may occur. furnished by Delta. Adjust the position of the clamps as shown on the drawings or as required to insure that the pump 18. Install the system header first: Typical layout will be Filter... - Page 9 Replacement parts or components may be obtained from your local distributor or directly from Delta Treatment Systems. COMPLAINTS: In order for Delta Treatment Systems to properly address any complaints we require that you put in writing the date and nature of the complaint as detailed as possible. This must include the serial number of your system.
- Page 10 CAPACITY OF ROUND TANKS Per Foot of Depth Diameter Gallons Area Sq. Ft. Diameter Gallons Area Sq. Ft. 23.50 3.14 211.51 28.27 2' 6" 36.72 4.909 6' 6" 248.23 35.18 52.88 7.069 287.88 38.48 3' 6" 71.97 9.621 7' 6" 330.48 44.18 94.00...
-
Page 11: General Description Of Operation
GENERAL DESCRIPTION OF DESCRIPTION OF CONTROL FLOATS OPERATION Float FS1 is a wide angle float that when up, permits the pump to run and when down, keeps the pump from running Upon power up at panel there is a 2 minute time delay before and pumping dry. - Page 12 ELECTRICAL COMPONENT INFORMATION & DRAWINGS Other drip systems and panels are available that have multiple circuit feeds, utilize solenoid field dosing valves and have dual filters. Upon power up the clock screen may not be displayed. The clock Setting the PLC screen is considered the “main”...
-
Page 13: Plc Parameters
PLC PARAMETERS Block Description Factory Setting PLC Nomenclature T = Run time 12 minutes 12:00 m TL = Off time 2 hours 02:00 h Off time during override period 1 hour 01:00 h FIlter flush time after pump turns on 1 minute 01:00 m Filter drain time after pump turns off... - Page 14 9125 Comar Drive, Walker, TN 70785...
- Page 15 9125 Comar Drive, Walker, TN 70785...
- Page 16 9125 Comar Drive, Walker, TN 70785...
- Page 21 9125 Comar Drive, Walker, TN 70785...
- Page 22 9125 Comar Drive, Walker, TN 70785...
- Page 23 9125 Comar Drive, Walker, TN 70785...
- Page 24 9125 Comar Drive, Walker, TN 70785...
- Page 25 9125 Comar Drive, Walker, TN 70785...
- Page 28 9125 Comar Drive, Walker, TN 70785...
- Page 29 9125 Comar Drive, Walker, TN 70785...
- Page 30 9125 Comar Drive, Walker, TN 70785...
- Page 31 9125 Comar Drive, Walker, TN 70785...
-
Page 32: Limited Warranty
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply. Sole obligation under this warranty is as follows: Delta Treatment Systems shall fulfill this warranty by repairing or exchanging any component part, F.O.B. factory that in Delta Treatment Systems judgment shows evidence of defects, provided said component part has been paid for and is returned through an authorized dealer, transportation prepaid.