Related Manuals for Associated Electrics TEAM ASSOCIATED Reflex 14MT
Summary of Contents for Associated Electrics TEAM ASSOCIATED Reflex 14MT
- Page 2 • Green Slime shock lube (AE Part # 1105) • Wire Cutters • FT Dual Turnbuckle Wrench (#1114) • FT Universal Tire Balancer (#1498) • Soldering Iron Associated Electrics, Inc. Customer Service 21062 Bake Parkway. Tel: 949.544.7500 Lake Forest, CA 92630 Fax: 949.544.7501...
- Page 3 :: Hardware - 1:1 Scale View :: Hardware - 1:1 Scale View Flat Head (fhcs) Cap Head (shcs) Ball Bearings 2.5x10mm (31350) 2.5x12mm (8691) 4x7x2.5mm (21512) Flat Head (fhst) Set Screws 4x8x3mm (21512) 3x2.5mm (31500) 2x8mm (21546) 8x12x3.5mm (21512) 3x3mm (25225) 2.6x8mm (21546) 3x8mm (4670) 2.6x10mm (21546)
- Page 4 :: Quick Start Guide Quick Start Guide Battery Charging Steps and Safety: Remove the battery from the vehicle before charging. Place battery on a fire resistant surface. Avoid any contact with water or other liquids. Be sure to select the correct charging mode for the type of battery you are charging.
- Page 5 4/23 :: Quick Start Guide Quick Start Guide - (cont.) - (cont.) Radio System Tuning and Controls: RULE: Transmitter on First/Vehicle on Second, Vehicle off First/ Transmitter off Last! Slide the battery cover to remove cover. Install alkaline or rechargeable AA size batteries into the battery holder.
- Page 6 :: Step 1 Step 1 21516 21516 Washer Washer 4x8x0.5mm 4x8x0.5mm 21530 21530 O-Ring O-Ring 3.8 x 1mm 3.8 x 1mm 21529 21529 Diff sun Diff 21529 gear case Diff 21524 21516 Diff 21524 outdrive Diff 1.5 x 6mm outdrive :: Step 2 Step 2 21529...
- Page 7 :: Step 4 Step 4 21516 21516 Washer Washer 4x8x0.5mm 4x8x0.5mm 21529 21530 21530 Diff sun O-Ring O-Ring 21516 gear 3.8 x 1mm 3.8 x 1mm 1.5 x 6mm 21529 21529 Diff Diff case 21524 21524 Center Diff diff outdrive shaft :: Step 5 Step 5...
- Page 8 :: Step 7 Step 7 Top of set screw head 4670 should be flush with 3x8mm the top of the chassis set screw 21570 Chassis :: Step 8 Step 8 21524 Center diff outdrive 21516 21563 21512 Metal 1.5 x 6mm 4x8x3mm pinion bearing...
- Page 9 :: Step 10 Step 10 89215 21546 M2.5 21512 M2.6x8mm locknut 4x7x2.5mm 21509 21509 BHST bearing Steering rack bushing 21510 Steering post 21522 21505 Ball stud 21505 Steering 12.5mm bellcrank Steering 31350 bellcrank (left) M2.5x10mm (right) FHCS :: Step 1 Step 11 1 31520 21504...
- Page 10 :: Step 1 Step 13 3 21546 M2.6x10mm 21621 BHST Bumper 21505 brace Shock tower 29277 support, rear 21546 21621 M2.6x8mm Front BHST bumper :: Step 14 4 21621 Body post 21503 Shock tower, rear 21173 Body clips 21621 21546 21621 21546 M2.6x10mm...
- Page 11 :: Step 16 Step 16 21546 M2.5x8mm BHST 21621 Skid plate, 21546 front M2.5x10mm FHST :: Step 17 Step 17 21522 Ball stud 21517 21546 12.5mm Universal M2.6x8mm drive shaft BHST 21508 Steering block, left 21521 21507 Crush Caster tube block, left 21523...
- Page 12 :: Step 19 Step 19 21502 21501 Rear arms mount, C 21511 21501 Inner Arm mount hinge pin, bushing 3x47mm 21502 21501 Rear arm 21546 spacers M2.6x6mm mount, D BHST :: Step 20 Step 20 21522 21518 Ball stud bone 12.5mm axle 21521...
- Page 13 :: Step 22 Step 22 Step 22 21577 Pivot 21514 21513 ball Ball Cup M3x35mm turnbuckle Front Camber Turnbuckle Orient the flange to the left throughout the 20.00mm car. It indicates which end 8691 has the left hand threads! M2.5x12mm BHCS Build x2 (right and left side) :: Step 23...
- Page 14 :: Step 25 Step 25 21538 21536 E-clip Shock 21537 Shock 21530 piston Shock 21534 cap o-ring Shock body, Front Shock Fluid: front (short) 30wt #5422 21534 21535 21537 Rear Shock Fluid: Shock body, Shock shaft, 21530 Shock 30wt #5422 rear (long) front (3x37mm) Shock...
- Page 15 :: Step 28 Step 28 21577 Pivot 21577 ball Pivot ball 31521 M2.5x8mm 31521 BHCS M2.5x8mm BHCS 25182 21582 M2.5x12mm M2.5x12mm BHCS Build x2 (right and left side) BHCS :: Step 29 Step 29 21621 Wheel support 21621 31521 Wheelie M2.5x8mm bar wheel BHCS...
- Page 16 :: Step 31 Step 31 Set The Gear Mesh: To set the gear mesh, push the teeth of the motor mount cam #21531 into the corresponding tooth pattern of the motor mount insert. Once the teeth are seated, you should be able to rock the spur gear back and forth without making the pinion gear move.
- Page 17 :: Step 33 Step 33 On/Off Switch Receiver 21505 Battery strap 21173 Body clips Battery :: :: Step 34 Step 34 21173 Body clips 21620 14MT mounted wheel and tire 91738 M4 serrated 21622 - Reflex 14MT Body Set, Clear nuts, black 21623 - Reflex 14MT Body Set, Blue/Green...
Need help?
Do you have a question about the TEAM ASSOCIATED Reflex 14MT and is the answer not in the manual?
Questions and answers