Extension Cords - Craftsman 315.26921 Operator's Manual

_ WARNING:Whenservicing, useonUy i denficaU
Craftsman repUacement parts.Useofanyother
partmaycreatea hazard or causeproduct
damage.
GENERAL
Orfiythe partsshown onthepartsHst, a reintended to
berepaired or repUaced by thecustomer. AH other
partsrepresent an important partofthedouMe
insuUafion system andshouUd beserviced onUy b ya
qualified Searsservice technician.
AvoidusingsoUvents whencleaning pUasfic parts.
MostpUastics aresuscepfiMe t odamage fromvarious
typesofcommerdaU soUvents andmaybedamaged
bytheiruse.UsedeancUoths toremove dirt,carbon
dust,etc.
_1_ WARNING:Donotat timeUet brakefluids,
any
gasoline, p etroleum-based products, p enetrating
oils,etc.comeincontact w ithplasticparts. T hey
contain chemicals t hatcandamage, weaken or
destroy plastic.
It hasbeenfoundthatelectric toolsaresubject t o
accelerated w earandpossible premature f ailurewhen
theyareusedonfiberglass b oats, s portscars,
wallboard, spackling compounds, or plaster. T he
chipsandgrindings fromthesematerials arehighly
abrasive toelectric toolpartssuchasbearings,
brushes, commutators, etc.Consequently, it is not
recommended thatthistoolbeusedforextended
workonanyfiberglass material, wallboard, spackling
compounds, or plaster. D uring anyuseonthese
materials it is extremely i mportant thatthetoolis
cleaned frequently b y blowing withanairjet.
CUTTERS
Getfastermoreaccurate cuttingresultsbykeeping
cutters cleanandsharp. R emove allaccumulated
pitchandgumfromcutters aftereachuse.
Whensharpening c utters, s harpen onlytheinsideof
thecutting edge.Never g rindtheoutside diameter. Be
surewhensharpening t heendof a cutterto grindthe
clearance a nglethesameas originally g round.
COLLET
Dustandchipsmaycollectonthecolletfromtimeto
time,making it necessary t ocleanthecollet. T odo
so,remove thecolletassembly a ndwipeit witha
cleandryrag.Cleanthetaperintheshaftin thesame
manner. N everimmerse thecolletor endoftheshaft
in a solvent o r inwater.Beforereplacing t hecollet
assembly, puta dropof SAE30 motoroilonthe inside
ofthenut,onthethreads oftheshaft,andon the
taperintheshaft.Replace thecolletassembly onto
theshaftbyhandonly.Never t ighten thecolletnut
without a bit inthecollet.Thisactioncould
permanently damage thecollet.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore,
no further hJbrication is require&
EXTENSION CORDS
The use of any extension cord will cause some loss of
power. To keep the loss to a minimum and to prevent
tool overheating, use an extension cord that is heavy
enough to carry the current the tool will draw.
A wire gage size (A.W.G.) of at least 14 is
recommended for an extension cord 100 feet or less
in length. When working outdoors, use an extension
cord that is suitable for outdoor use. The cord's jacket
will be marked WA
,_ CAUTION: Keep extension cords away from the
cutting area and position the cord so that it will
not get caught on lumber, tools, etc. during
_ WARNING: Check extension cords before each
use. If damaged replace immediately. Never use
tool with a damaged cord since touching the
damaged area could cause electrical shock
resulting in serious injury.
Extension cords suitable for use with your router are
available at your nearest Sears Retail Store.
,_ WARNING: Always wear safety goggles or
safety glasses with side shields during power
tool operation or when blowing dust. If operation
is dusty, also wear a dust mask.
18