Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
2
Print only the pages for your vehicle using the advanced
options in the Print menu.
3
Install your Maestro RR according to the guide for your vehicle.
Pressing the printer icon or "quick printing" this document will print
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in
Page 1
Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Jeep Wrangler Jl With 5" radio 2018-2023 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
CH3 harness to adapter and skip to step 2. STEP 5 • Unbox the aftermarket radio and locate its main harness. • Connect all the harnesses to the Maestro RR module then • Cut and remove the black 20 pin connector from the HRR- test your installation.
STEP 5 SPEAKER* *REQUIRED ACCESSORY WHITE In vehicles without OEM amplifier, with OEM parking sensors BLACK WHITE MAESTRO RR MODULE STEP 3 CAN JUNCTION BLOCK (GREEN) UNPLUG BLACK N.C. UNPLUG ANY OF THE 2-PIN CONNECTORS IN THE CAN JUNCTION BLOCK.
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 9
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 10
Ram 1500 ClassiC with 3" oR 5" Radio 2019-2023 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 11
If using head unit adapter (sold separately), connect HRR- CH3 harness to adapter and skip to step 2. STEP 5 • Connect all the harnesses to the Maestro RR module then • Unbox the aftermarket radio and locate its main harness. test your installation.
Page 12
STEP 5 SPEAKER* *REQUIRED ACCESSORY WHITE In vehicles without OEM amplifier, with OEM parking sensors BLACK WHITE MAESTRO RR MODULE STEP 3 CAN JUNCTION BLOCK (GREEN) UNPLUG BLACK N.C. UNPLUG ANY OF THE 2-PIN CONNECTORS IN THE CAN JUNCTION BLOCK.
Page 15
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 16
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 17
Ram 1500 with 3" oR 5" Radio 2013-2017 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 18
STEP 4 the OEM settings menus, you must use an iDatalink compatible radio. • Connect all the harnesses to the Maestro RR module then test your installation. STEP 1 • If the vehicle is equipped with OEM parking assist and no...
Page 19
VEHICLE WHITE BLACK STEP 4 WITHOUT AMP SPEAKER* *REQUIRED ACCESSORY In vehicles without OEM amplifier, WHITE with OEM parking sensors BLACK WHITE MAESTRO RR MODULE BLACK N.C. N.C. AMP TURNON AMP TURNON N.C. HHR-CH3 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc.
Page 22
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 23
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 24
Ram 1500 with 3" oR 5" Radio 2018 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 25
STEP 5 • Unbox the aftermarket radio and locate its main harness. • Connect all the harnesses to the Maestro RR module then • Cut and remove the black 20 pin connector from the HRR- CH3 T-harness and connect the wires, shown in the wiring test your installation.
Page 26
STEP 5 SPEAKER* *REQUIRED ACCESSORY WHITE In vehicles without OEM amplifier, with OEM parking sensors BLACK WHITE MAESTRO RR MODULE STEP 3 CAN JUNCTION BLOCK (GREEN) UNPLUG BLACK N.C. UNPLUG ANY OF THE 2-PIN CONNECTORS IN THE CAN JUNCTION BLOCK.
Page 29
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 30
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 31
Ram 1500 with 5" Radio 2019-2023 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 32
If using head unit adapter (sold separately), connect HRR- CH3 harness to adapter and skip to step 2. STEP 5 • Connect all the harnesses to the Maestro RR module then • Unbox the aftermarket radio and locate its main harness. test your installation.
Page 33
STEP 5 SPEAKER* *REQUIRED ACCESSORY WHITE In vehicles without OEM amplifier, with OEM parking sensors BLACK WHITE MAESTRO RR MODULE STEP 3 CAN JUNCTION BLOCK (GREEN) UNPLUG BLACK N.C. UNPLUG ANY OF THE 2-PIN CONNECTORS IN THE CAN JUNCTION BLOCK.
Page 36
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 37
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 38
Ram 2500 & 3500 with 3" oR 5" Radio 2013-2018 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 39
STEP 4 the OEM settings menus, you must use an iDatalink compatible radio. • Connect all the harnesses to the Maestro RR module then test your installation. STEP 1 • If the vehicle is equipped with OEM parking assist and no...
Page 40
VEHICLE WHITE BLACK STEP 4 WITHOUT AMP SPEAKER* *REQUIRED ACCESSORY In vehicles without OEM amplifier, WHITE with OEM parking sensors BLACK WHITE MAESTRO RR MODULE BLACK N.C. N.C. AMP TURNON AMP TURNON N.C. HHR-CH3 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc.
Page 43
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 44
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 45
Ram 2500 & 3500 with 5" Radio 2019-2021 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 46
If using head unit adapter (sold separately), connect HRR- CH3 harness to adapter and skip to step 2. STEP 5 • Connect all the harnesses to the Maestro RR module then • Unbox the aftermarket radio and locate its main harness. test your installation.
Page 47
STEP 5 SPEAKER* *REQUIRED ACCESSORY WHITE In vehicles without OEM amplifier, with OEM parking sensors BLACK WHITE MAESTRO RR MODULE STEP 3 CAN JUNCTION BLOCK (GREEN) UNPLUG BLACK N.C. UNPLUG ANY OF THE 2-PIN CONNECTORS IN THE CAN JUNCTION BLOCK.
Page 50
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 51
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 52
Ram Chassis Cab with 3" oR 5" Radio 2013-2018 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 53
STEP 4 the OEM settings menus, you must use an iDatalink compatible radio. • Connect all the harnesses to the Maestro RR module then test your installation. STEP 1 • If the vehicle is equipped with OEM parking assist and no...
Page 54
VEHICLE WHITE BLACK STEP 4 WITHOUT AMP SPEAKER* *REQUIRED ACCESSORY In vehicles without OEM amplifier, WHITE with OEM parking sensors BLACK WHITE MAESTRO RR MODULE BLACK N.C. N.C. AMP TURNON AMP TURNON N.C. HHR-CH3 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc.
Page 57
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 58
PRODUCTS REQUIRED PROGRAMMED FIRMWARE: CH3-RR-AS iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-CH3 Installation Harness NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Page 59
Ram Chassis Cab with 5" Radio 2019-2021 WELCOME ADDITIONAL INFORMATION AND ACCESSORIES Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are HEAD UNIT ADAPTER: now a few simple steps away from ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 enjoying your new car radio with enhanced features.
Page 60
If using head unit adapter (sold separately), connect HRR- CH3 harness to adapter and skip to step 2. STEP 5 • Connect all the harnesses to the Maestro RR module then • Unbox the aftermarket radio and locate its main harness. test your installation.
Page 61
STEP 5 SPEAKER* *REQUIRED ACCESSORY WHITE In vehicles without OEM amplifier, with OEM parking sensors BLACK WHITE MAESTRO RR MODULE STEP 3 CAN JUNCTION BLOCK (GREEN) UNPLUG BLACK N.C. UNPLUG ANY OF THE 2-PIN CONNECTORS IN THE CAN JUNCTION BLOCK.
Page 64
The radio stays ON. Make sure the 2-pin connectors in the harness are connected as stated in step 2. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).