1. Manuals
  2. Brands
  3. SafeWaze Manuals
  4. Safety Equipment
  5. FS-EX210
  6. Manual

SafeWaze FS-EX210 Manual

Easy slider i-beam anchor adjustable
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
EASY SLIDER
I-BEAM ANCHOR
ADJUSTABLE FROM 4"-14"
Model # FS-EX210
IMPORTANT!!!
ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS.
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE FAMILIAR
WITH PERTINENT REGULATIONS GOVERNING THIS EQUIPMENT. ALL INDIVIDUALS WHO USE
THIS PRODUCT MUST BE PROPERLY INSTRUCTED ON HOW TO USE THIS DEVICE.
V2.4

Advertisement

Table of Contents
loading

Related Manuals for SafeWaze FS-EX210

Summary of Contents for SafeWaze FS-EX210

  • Page 1 EASY SLIDER I-BEAM ANCHOR ADJUSTABLE FROM 4”-14” Model # FS-EX210 IMPORTANT!!! ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE FAMILIAR WITH PERTINENT REGULATIONS GOVERNING THIS EQUIPMENT. ALL INDIVIDUALS WHO USE THIS PRODUCT MUST BE PROPERLY INSTRUCTED ON HOW TO USE THIS DEVICE.

  • Page 2: Use Instructions

    PURPOSE The FS-EX210 is an anchorage connector designed to function as an interface between the anchorage and a fall protection, work positioning, rope access, or rescue system for the purpose of coupling the system to the anchorage. Any references to “anchorage connector”...

  • Page 3: Component Materials

    PERFORMANCE: REGULATORY COMPLIANCE: Static Tensile Strength: 5000-lbf (22kN) ANSI Z359.1(07), ANSI Z359.7(11), Maximum Capacity: One worker with max OSHA 1926.502, OSHA 1910.66 weight of 310-lbs when used as a single point anchorage connector for personal fall COMPONENT MATERIALS: arrest or restraint system Aluminum: Cross Bar DIMENSIONS: Bronze: Clamps...
  • Page 4 LOADING CONDITIONS DIAGRAM Placement at or below a user’s working height requires integration of a compatible ANSI Z359.1 shock-absorbing lanyard that does not allow the user to extend more than 6 feet (in any direction) from the anchorage connector before the shock absorber is activated. The beam anchor must be attached to the I-beam flange facing the user (top flange if above, bottom flange if below, etc.).
  • Page 5 *The user shall be equipped with a means of limiting the maximum dynamic forces exerted on the user during the arrest of a fall to a maximum of 8 kN (1800-lbf ). (ANCHOR POINT) WORK SURFACE Inspect retaining bushing for wear or damage.

  • Page 6: Warning Label Locations

    WARNING: All persons using this equipment must read, understand and fol- low all instructions. Failure to do so could result in serious injury or death. FS-EX210 | Beam Anchor ATTENTION: Do not remove tag. This unit must be inspected before each use. Any unit that has seen fall arrest forces must be removed from service.

  • Page 7: Maintenance, Cleaning And Storage

    MAINTENANCE, CLEANING AND STORAGE Cleaning periodically will prolong the life and proper functioning of the product. The frequency of cleaning should be determined by inspection and by severity of the environment. Clean with compressed air and/or a stiff brush using plain water or a mild soap and water solution. Do not use any corrosive chemicals that could damage the product.
  • Page 8 LIMITED REMEDY: Upon notice in writing, SafeWaze will repair or replace all defective items at SafeWaze’s sole discretion. SafeWaze reserves the right to require that the defective item be returned to its plant for inspection before determining the appropriate course action. Warranty does not cover equipment damage resulting from wear, abuse, damage in transit, failure to maintain the product or other damage beyond the control of SafeWaze.

Table of Contents