Vaporesso GEN 200, GEN 80 S - Vape Kit Manual

EXPLOADED VIEW

Thank you for choosing Vaporesso product. Please read this instruction carefully before use to ensure a perfect experience.

If there is any additional requirement about this product, please consult the local agent or contact us through our website: www.vaporesso.com

VAPORESSO GEN 200


VAPORESSO GEN 80 S

SPECIFICATION

VAPORESSO GEN 200:

Dimensions: 138.5*44*29mm
TANK Capacity: 8ml/2ml(TPD)
Coils & Suggested Wattage: GTi 0.2Ω MESH Coil (60-75W); GTi 0.4Ω MESH Coil (50-60W)
Battery Capacity: 2 x 18650
Output Power: 5-220W
Charging Current: DC 5V/2A, Type-C
Battery Display: 0.96'' TFT Screen

VAPORESSO GEN 80 S:

Dimensions: 140.5 x 34 x 25.5 mm
TANK Capacity: 5ml/2ml(TPD)
Coils & Suggested Wattage: GTi 0.2Ω MESH Coil (60-75W); GTi 0.4Ω MESH Coil (50-60W)
Battery Capacity: 1 x 18650 Battery (Not Included)
Output Power: 5-80W
Charging Current: DC 5V/2A, Type-C
Battery Display: 0.96'' TFT Screen

PACKING LIST

VAPORESSO GEN 200:

1 x VAPORESSO GEN 200 MOD
1 x VAPORESSO iTANK (8ml/2ml TPD)
1 x GTi 0.2Ω MESH Coil (Pre-installed)
1 x GTi 0.4Ω MESH Coil (In-BOX)
1 x Extra Glass Tube
3 x O-ring
1 x Type-C Cable
1 x User Manual
1 x Warranty Card

VAPORESSO GEN 80 S:

1 x VAPORESSO GEN 80 S MOD
1 x VAPORESSO iTANK (5ml/2ml TPD)
1 x GTi 0.2Ω MESH Coil (Pre-installed)
1 x GTi 0.4Ω MESH Coil (In-BOX)
1 x Extra Glass Tube
3 x O-ring
1 x Type-C Cable 1 x User Manual
1 x Warranty Card

USER INTERFACE

USER INSTRUCATIONS

1. Install the Tank
   Install the tank to the battery by screwing the 510 thread. Make sure they are firmly connected.
2. Replace the Coil
   • Unscrew the thread base from the tank;
   • Pull out the used coil from the tank;
   • Install a new coil to the tank;
   • Reattach the thread base into place.
   • * Refer to the figure 1.
     
3. Fill E-liquid
   • Push the top cap according to the arrow direction;
   • fill e-liquid through the hole, then lock the top cap in place after filling is finished.- Please wait 5 minutes for the e-liquid to soak into the coil completely.
     * Refer to the figure 2.
     
4. Adjust the Airflow
   To adjust the airflow volume, please rotate the air-inlet ring on the bottom of the tank.
5. Power On/Off the Device
   Power on/off: press the power button 5 times in 2s.
6. Power Adjustment
   GEN 200 & 80 S Kit is using the powerful GTi coil platform, and the suggested power need to be noticed before start vaping.

   GTi MESH Coils	GTi 0.2Ω MESH	GTi 0.4Ω MESH
   Suggested Power	60-75W	50-60W

7. Start Vaping
   Press the power button to enjoy extraordinary vaping experience.
8. Charge the Battery
   After connecting the Type-C cable to the battery, the battery indicator and remaining charging time will be showed on the screen.
9. Lock or unlock the device
   Press the fire button 3 times, then the +, - and mode buttons will be locked. In the same way, the buttons will be unlocked and the screen will be unlocked.
10. Choose a Mode
    1. Long press the mode button for main mode selection ( Pulse Mode/F(t) Mode/VWN Mode).
    2. Press the mode button 3 times continuously for secondary menu setting.

*F(t): F(t) MODE (DEFAULT)
F(t) MODE is by adjusting temperature, heating speed and time, F(t) mode releases the flavors of e-liquid adequately, delivering the perfect balanced tasting experience consistently from the first puff throughout.

*PUL: PULSE MODE
PULSE MODE is a mode to improve vaping experience through constant voltage output, delivering optimal flavor production, throat hit, nicotine satisfaction, and perfect temperature cloud continuously.

*VWN: VARIABLE WATTAGE MODE/ SIMPLE MODE
VWN MODE is a normal mode of output wattage, you can according to the coil resistance to adjust the best wattage for your needs. The user interface shows wattage, resistance and puff counter for your immersive vaping experience.

*DIY: DIY MODE
You can choose traditional VW (H, N, S), VV, BP (Bypass) modes in this section.

*SET: SYSTEM SET
System setting includes DEFAULT, SMART VW, PUFF, and VERSION options.
SMART VW: when this function is turned on and a TANK is installed, the system will recommend the best power.

PROTECTIONS

1. Short circuit protection & Low resistance protection:
   When the load resistance is less than 0.05 Ω, press the ignition key devise will enter the short circuit protection and close the output, screen will display "SHORT ATOMIZER".
2. Low resistance protection:
   When the load resistance is less than 0.09 Ω, press the ignition key devise will enter the Low resistance protection and close the output, screen will display "LOW RESISTANCE".
3. No load protection:
   When no load resistance is detected, press power button could trigger the no load protection, the device will close the output, at the same time OLED display will show "CHECK ATOMIZER".
4. High resistance protection:
   When the load resistance is greater than 5Ω, press power button could trigger the high resistance protection, the device will close the output, at the same time OLED display will show " CHECK ATOMIZER ".
5. Low voltage protection:
   When the voltage of the battery cell is lower than 3.3V, press power button could trigger the low voltage protection, the device will close the output, at the same time OLED display will show "LOW BATTERY".
6. PCBA(Printed Circuit Board Assembly):
   When the temperature of PCBA sensor reaches 60-85 degrees, screen display "OVER HEAT" and output is closed.
7. Over discharge protection:
   In the discharge process, when the voltage between PCBA power supply welding spot B+ and B- is less than 2.9v, the output is automatically closed.
8. USB High Voltage Input Protection:
   Switching in the charger, stop charging when the input voltage to USB port exceeds 6V and is lower than 30V.
9. Over charge protection:
   During the charging, the battery voltage will rises to 4.2V+/-0.3V,the screen will display "100%"
10. Auto-shut off protection
    When POWER button is held for 10±1 seconds, the device will close the output, at the same time OLED display will show "OVER TIME".

CAUTIONS

1. Please turn off the device when it is not in use.
2. Do not leave the charging device unattended.
3. Do not drop, throw or abuse your device, which may cause damage.
4. Please use a standard USB output charger with proper charging current and voltage range.
5. Keep away from the water or any flammable gas, liquid.
6. Keep away from corrosive chemicals.
7. Do not expose the device to direct sunlight, dust, moisture or mechanical shock.
8. Do not expose the device to extreme temperature. (Recommended temperature range: -10~45℃ /14~113℉ while using and -10~45℃ /14~113 ℉ while storing).
9. EEE Recycling: The product should not be treated as household waste, instead, it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
10. Battery Recycling: The product battery should not be treated as household waste, instead, it should be handed over to the applicable used battery collection point for recycling.
11. Only have your device repaired by Vaporesso. Do not attempt to repair it by yourself as damage or personal injury may occur;
12. Do Not use batteries with broken surface, overheating, leakage and strange odor;
13. Charge the battery indoors only;
14. Recycle batteries in accordance with local laws and regulations.
15. Please use high-rate discharge batteries(≥25A).

WARNING

This refillable electronic cigarette is intended for use with compatible e-liquid, which may contain nicotine. Nicotine is an addictive substance and it is not suitable or recommended to use in following cases:

1. This device is not suitable for:
   • Persons under the legal smoking age.
   • Persons experiencing heart disease, stomach or duodenal ulcers, liver or kidney problems, long-term throat disease or difficult breathing due to bronchitis, emphysema or asthma. - Persons with an overactive thyroid gland or experiencing phaeochromocytoma (a tumour of the adrenal gland that can affect blood pressure).
   • Persons taking certain medications like Theophylline, Ropinirole or Clozapine and etc..
2. This device is not recommended for
   • Non-smokers
   • Pregnant or breastfeeding women
3. You may experience the following results if you use nicotine containing e-liquid with this product. If it happens, please consult a healthcare professional and show them this leaflet if possible:
   Feeling faint/Nausea /Dizziness/Headache /Coughing/Irritation of the mouth or throat/ Stomach discomfort/Hiccups/Nasal congestion/Vomition/Chest palpitations/pain or an irregular heart rate

This device should not be used by persons under the legal smoking age.