Table of Contents
Advertisement
ARGUSÖ0ORT
2EPLICATOR
Q7PÇQÖ9 A67
AKINGÖ9OURÖ OBILEÖ,IFEÖ%ASIER
AKINGÖ9OURÖ OBILEÖ,IFEÖ%ASIER
ISITÖOURÖ7EBÖSITEÖATÖWWWTARGUSCOM
&EATURESÖANDÖSPECIFICATIONSÖAREÖSUBJECTÖTOÖCHANGEÖWITHOUTÖNOTICE
ÖÖÖ4ARGUSÖ'ROUPÖ)NTERNATIONALÖANDÖ4ARGUSÖ)NC
!
B
H
B
T
M
A
S
L
P
N
Y
L
A
T
H
K
S
RUSSELS
ANNOVER
ARCELONA
OKYO
ILANO
MSTERDAM
INGAPORE
ONDON
ARIS
EW
ORK
OS
NGELES
ORONTO
ONG
ONG
YDNEY
Advertisement
Table of Contents
Related Manuals for Targus PA075U
Summary of Contents for Targus PA075U
- Page 1 ARGUSÖ0ORT 2EPLICATOR Q7PÇQÖ9 A67 AKINGÖ9OURÖ OBILEÖ,IFEÖ%ASIER AKINGÖ9OURÖ OBILEÖ,IFEÖ%ASIER ISITÖOURÖ7EBÖSITEÖATÖWWWTARGUSCOM &EATURESÖANDÖSPECIFICATIONSÖAREÖSUBJECTÖTOÖCHANGEÖWITHOUTÖNOTICE ÖÖÖ4ARGUSÖ'ROUPÖ)NTERNATIONALÖANDÖ4ARGUSÖ)NC ! RUSSELS ANNOVER ARCELONA OKYO ILANO MSTERDAM INGAPORE ONDON ARIS NGELES ORONTO YDNEY...
-
Page 2: System Requirements
Introduction Congratulations on your purchase of the Targus USB Mobile Port Replicator. This ultra portable expansion module directly connects to a desktop or notebook computer via a Universal Serial Bus (USB) port. The port replicator provides the following ports: ®... - Page 3 WARNING: You must install the port replicator software BEFORE connecting it to your computer. Otherwise, the port replicator will not work properly. Installing the Port Replicator Drivers 1 Turn on your computer. 2 Insert the driver software CD into your computer’s CD- ROM drive.
- Page 4 1 Turn off your computer. 2 (Model PA095 only) Open the USB cable compartment, located on the bottom of the port replicator, and uncoil the cable. 3 Connect the supplied AC power adapter to the AC power jack on the port replicator. 4 Plug the USB connector end of the USB cable into the USB port of your computer.
-
Page 5: Led Status Indicator Lights
The Completing the Found New Hardware Wizard screen appears. 2 Click Finish and repeat as needed for each device. 3 Restart your computer. When your computer restarts, the port replicator/dock should be completely configured. LED Status Indicator Lights Once all device drivers are installed, the LED status indicator lights glow and you can connect devices to the port replicator. - Page 6 The port replicator supports hot swapping of the network cable. Connecting Devices to the Port Replicator When connecting new devices to the port replicator, you may need to install additional software drivers. Consider the following guidelines: • The device drivers install automatically. •...
- Page 7 PS/2 Port To connect a PS/2 device, such as a mouse or keyboard, plug it into a PS/2 port on the port replicator and begin using the device. Serial Port Connecting and Configuring a Modem To connect a serial modem: 1 Attach the cable connector to the serial port on the port replicator.
-
Page 8: Parallel Port
Parallel Port Connecting and Configuring a Printer for the First Time To connect a parallel printer: 1 Attach the cable connector to the parallel port on the port replicator. 2 Install the printer software driver according to the instructions that come with the device. 3 When prompted to select a port, choose PB1284-1 (USB port). -
Page 9: Special Notes
(Model PA095 only) Ethernet Port To connect an RJ-45 Ethernet cable, attach the cable connector to the Ethernet port on the port replicator. Additional procedures to connect to an actual network depend on the type of network you are using. Contact your network administrator for detailed instructions. -
Page 10: Product Limitations
Product Limitations General The port replicator splits a single connection among a variety of devices and connections. Some devices, which use large amounts of bandwidth, such as printers and digital cameras, can consume all available resources and may interfere with the performance of other devices. You may experience some temporary halting of some devices when a high data transfer is occurring. -
Page 11: Troubleshooting
However, the mouse will continue to work as a standard, two-button mouse and the keyboard as a standard keyboard. Troubleshooting Device Not Working • Make sure that the device is fully inserted into the correct port on the port replicator. •... - Page 12 Sample Device Manager tab (Windows From the Device Manager window, expand the following: • Human Interface Devices — displays PS/2 Keyboard and Mouse Adapter when a PS/2 device is plugged in. • Network adapters — displays USB Ethernet 10/100 (Model PA095 only) •...
- Page 13 If the operating system does not detect automatically that your modem is assigned to Serial USB (COMx), rerun the Hardware Wizard and choose Select from a list instead of Autodetect. Then, select Serial USB (COMx) as the COM port. Error Message on Your Handheld Computer If the error message “Connection Not Established”...
-
Page 14: Technical Support
(if applicable). Warranty Targus warrants this product to be free from defects in materials and workmanship for one year. If your Targus accessory is found to be defective within that time, we will promptly repair or replace it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. -
Page 15: Fcc Statement
International Business Machines Corporation. Zip drive is a registered trademark of Iomega Corporation.Features and specifications are subject to change without notice. All other trademarks and registered trademarks are the property of their respective owners. (c) 2004 Targus Group International and Targus, Inc., Anaheim, CA 92806.