Sangean U4X - Radio Manual

AC OPERATION

Before you plug the AC cable into an AC socket, be sure that the voltage is fully compatible with this radio.
The hooks on the back of the radio are designed to store the AC cable when you are not using it.

DC IN OPERATION

This radio may be powered via its DC IN socket, which allows the use of a 12V DC adaptor (not included).

BATTERY OPERATION

The radio may be powered by the built-in rechargeable battery.

This radio is equipped with a fully integrated rechargeable 10.8V 18650 / 3200mA 31.1W lithium battery which automatically connects when the AC power supply is not in use, and recharges when the radio is on AC power mode.

GENERAL OPERATION

1. Press the POWER button to turn 1 on the radio.
   
2. Press the SOURCE button to select the desired operating mode.
   
3. Press and hold the MENU button to access the menu system of each 2 mode. Highlight the menu item using the TUNING knob. Press the TUNING knob to select that item. Press the MENU button to go back to the previous page, or to exit the menu option without saving.
   
4. The INFO button allows the display of information relating to the radio station or music file being played. Press the INFO button to cycle through the different options.
5. In the FM mode, rotate the TUNING 3,5 knob to increase / decrease the frequency with steps of 0.05MHz or 8,11 rotate the TUNING knob and then press it to automatically scan for the next radio station with a higher / lower frequency.
   
   
6. Rotate the VOLUME knob to adjust the sound level as needed.
   
7. Storing a preset: To store the currently playing radio station as a preset, press and hold one of the radio's PRESET buttons (1- 5) to store the station in that position in the current page until the confirmation message appears on the LCD display.
   Alternatively, press the PAGE button to select the desired preset pages 1 to 5. Then press and hold the desired PRESET button until the confirmation message appears on the LCD display.
   
8. Recalling a preset: Press a PRESET button to recall the station stored in that position in the currently selected page.
   Alternatively, press the PAGE button to access a different preset memory page. Then rotate the TUNING knob to select a station and press to confirm.
9. Press the EQ button to access the EQ menu. Then rotate the VOLUME knob to select an EQ profile or select "My EQ Setup" option and subsequently set the "Treble" / "Middle" / "Bass" level.
   Press the VOLUME knob to confirm the setting.
   
10. Press the LOUDNESS button to enable or disable the radio's loudness function.
    
11. Press the button to enter the "Timers" menu, then set the "Alarm" / "Sleep" / "Timer" using the TUNING knob.
    

USB CHARGE

Your radio has a USB port on its left-hand side, which can be used to charge smartphones and similar low voltage devices. The USB port is protected by a rubber cover. When the port is not in use, the rubber cover should always be closed to prevent dust or dirt from entering.

When the radio is battery operated, the option "USB Charge" will appear in the System Settings. The USB Charge feature can be used to charge external USB devices and can be enabled or disabled by selecting "On" or "Off". In order to save battery power, this feature is disabled (Off) by default and needs to be enabled (On) in order to charge external USB devices. However, when the radio is in USB mode, external devices can always be charged, regardless of whether the USB Charge function has been enabled or disabled.

When the radio is powered from the mains or by a 12V DC IN adaptor (not included), external USB devices can always be charged, even when the radio is in Standby mode.

When the radio is battery operated, external USB devices cannot be charged if the radio is turned off.

Once the external device is fully charged, disconnect it from the radio and put back the rubber cover.

Recharge time may vary and usually takes longer than when using a standard charger.

SPECIFICATIONS

Sangean reserves the right to amend the specifications without notice.

RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

For full documentation on all of the U4X's functionality, please visit the website below or scan the QR code to download the full manual.
https://www.sangean.com