Advertisement
Quick Links
Advertisement
Related Manuals for CHNT Power CPS SCA2KTL-PS1/EU
Summary of Contents for CHNT Power CPS SCA2KTL-PS1/EU
- Page 1 CPS SCA2/3/3.6KTL-PS1/EU CPS SCA4.6/5/6KTL-PSM1/EU...
- Page 4 This manual is applicable to following inverters: CPS SCA�/�/�.�KTL-PS�/EU CPS SCA�.�/�/�KTL-PSM�/EU...
- Page 10 Inverters have been tested as per AS/NZS ����.�:���� for three-phase combinations. And the Maximum number of single-phase inverters used in three-phase combinations is �.
- Page 11 � .�...
- Page 15 Do not install the inverter on flammable building materials or in an DANGER area where flammable or explosive materials are stored. Do not install the inverter in a place where personnel are likely to CAUTION come into contact with its enclosure and heat sinks to avoid electrical shock/burn.
- Page 22 � .�...
- Page 24 � .�...
- Page 27 Secure the PGND cable (done by step 1 & 2) using the ground screw and tighten the screw using a socket wrench (torque 1.2 N·m),as shown in Figure 5.4. Figure 5.4 Secure the PGND cable The AC power cable and AC terminals have been prepared. a.
- Page 28 An independent circuit breaker must be installed on the AC side of each WARNING inverter to ensure that the inverter can be safely disconnected from the power grid. Do not connect loads between the AC output terminals of the inverter WARNING and circuit breaker.
- Page 29 Line Neutral Earth Ground, neutral, and line wires must correspond to G, N, and L terminals NOTICE of AC connectors respectively. Otherwise, the faulty connection will lead to the inverter performance failure.
- Page 30 �...
- Page 31 �...
-
Page 34: Download App
Download APP Scan the QR code to download "Chint Connect" APP: Note: You need to grant all access rights in all pop-up windows when installing the APP or settingyour phone. Chint... - Page 35 Enabling Bluetooth communication on your mobile phone, you can set parameters about power limit function to control inverter. Chint In general, the power limit function will be realized by wiring the digital meter externally and setting the parameters internally in APP. (Find specific setting instruction in clause 5.5.1&5.5.2) Yet, except “external wiring system+APP setting”...
- Page 36 5.5.2.1 Power Limit Control Setting：Wiring diagram of Inverter+Meter 5.5.2.2 Power Limit Control Setting：APP Settings Default Setting steps: --Power limit function set to “Digital Power Meter” --Set the meter position to “on load” or 》 “on grid” according to the meter installed;...
- Page 37 �.�.� Generation and Export Limits The generation control function is used to control the active or apparent power output levels of an inverter or multiple inverter combination such that it meets a predetermined generation output level that may be less than the total rated apparent power of the inverter or multiple inverter combination.
- Page 38 �.�.� Country code configuration (only for Administrator) Click "INV/ESI settings" button to enter the "Inverter Settings" page. Click "Initial" button to set grid code, then get back and click "RW Register" button to set register parameters or modbus address if necessary. Now you can click "Overview"...
- Page 39 �.� DRM Connection In accordance with AS/NZS 4777.2:2020, the inverter should support DRM( Demand Response Mode) function. The port definition of DRM function and methods of its connection are shown as below. DRM � DRM � METHOD FOR ASSERTING DRM Mode Function DRM �...
- Page 42 (Earth Fault) (Earth Fault)
- Page 43 If the Inverter is malfunctioning, a samll horn symbol will appear in the APP interface. You can get specific fault information by clicking on the small horn symbol as below images. Via-Gateway 5***41122312 Running Inverter ID 1 CPS SCAxxxxxxxxxxxx [ FW Master 0.00 ; Dupty 0.00 ] SN 0001012311321314124 Warranty period ends on 2032-10-01 B1- PV insulation abnormal...
- Page 50 Model CPS SCA�KTL-PS�/EU CPS SCA�KTL-PS�/EU CPS SCA�.�KTL-PS�/EU Efficiency Max.efficiency ��.�% ��.�% ��.�% European efficiency ��.�% ��.�% ��.�% Input (PV) Max. PV configuration (STC¹) ���% Max. input voltage (V) ��� Rated input Voltage (V) ��� Max. input current (A) �� Maxmum inverter backfeed current �...
- Page 51 Protection DC Switch Support Anti-islanding protection Active frequency drift AC overcurrent protection Support AC short circuit protection Support DC reverse connection Support Surge Arrester DC Type III (Optional) / AC Type III Insulation detection Support Leakage current protection Support Inverter topology Non-isolated General Topology...
- Page 52 Model CPS SCA�.�KTL-PSM�/EU CPS SCA�KTL-PSM�/EU CPS SCA�KTL-PSM�/EU Efficiency Max.efficiency ��.�% ��.�% ��.�% European efficiency ��.�% ��.�% ��.�% Input (PV) ���% Max. PV configuration (STC�) ��� Max. input voltage (V) ��� Rated input Voltage (V) ��(�*��) Max. input current (A) Maxmum inverter backfeed current to array (A) �...
- Page 53 Protection Support DC Switch Active frequency drift Anti-islanding protection Support AC overcurrent protection Support AC short circuit protection Support DC reverse connection DC Type III (Optional) / AC Type III Surge Arrester Support Insulation detection Support Leakage current protection Non-isolated Inverter topology General Transferless...
Need help?
Do you have a question about the CPS SCA2KTL-PS1/EU and is the answer not in the manual?
Questions and answers