Français - HIKVISION DS-2XC6284G0-L Quick Start Manual

used batteries according to the instructions. Improper
replacement of the battery with an incorrect type may defeat a
safeguard (for example, in the case of some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result in an
explosion. Do not leave the battery in an extremely high
temperature surrounding environment, which may result in an
explosion or the leakage of flammable liquid or gas. Do not subject
the battery to extremely low air pressure, which may result in an
explosion or the leakage of flammable liquid or gas. + identifies
the positive terminal(s) of equipment which is used with, or
generates direct current. - identifies the negative terminal(s) of
equipment which is used with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles, should be placed
on the equipment. The serial port of the equipment is used for
debugging only.
Hot Surface Prevention
marked item can be hot and should not be touched without taking
care. For device with this sticker, this device is intended for
installation in a restricted access location, access can only be
gained by service persons or by users who have been instructed
about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
Installation
Install the device according to the instructions in this manual. To
prevent injury, this device must be securely attached to the
installation surface in accordance with the installation instructions.
Never place the equipment in an unstable location. The
equipment may fall, causing serious personal injury or death. If the
device needs to be wired by yourself, select the corresponding
wire to supply power according to the electric parameters labeled
on the device. Strip off wire with a standard wire stripper at
corresponding position. To avoid serious consequences, the length
of stripped wire shall be appropriate, and conductors shall not be
exposed. Make sure that the power has been disconnected before
you wire, install, or disassemble the device.
Power Supply
Device powered by Safety Extra-Low Voltage (SELV): The power
source should meet limited power source or PS2 requirements
according to IEC 60950-1 or IEC 62368-1 standard.
Device powered by AC mains supply voltage: The equipment must
be connected to an earthed mains socket-outlet. An appropriate
readily accessible disconnect device shall be incorporated external
to the equipment. An appropriate overcurrent protective device
shall be incorporated external to the equipment, not exceeding
the specification of the building. An all-pole mains switch shall be
incorporated in the electrical installation of the building. If the
device is powered by terminals connected to the power cord,
ensure correct voltage and wiring of the terminals for connection
to mains supply. The equipment has been designed, when
required, modified for connection to an IT power distribution
system.
Conformité à la réglementation et consignes de sécurité
CAUTION: Hot parts! Burned fingers
when handling the parts. Wait one-half
hour after switching off before handling
parts. This sticker is to indicate that the
White Light Illuminator (If supported)
The white supplement light source of the camera is classified as
Risk Group 2 (RG2).
Possibly hazardous optical radiation emitted from this product. DO
NOT stare at operating light source. May be harmful to the eyes.
Wear appropriate eye protection or DO NOT turn on the white
light when you assemble, install or maintain the camera.
The device should be positioned so that prolonged staring into its
white light source at a distance closer than 0.6 m is not expected.
The Risk Group 1 (RG1) hazard distance of the device is 0.25 m.
CAUTION Possibly hazardous optical radiation emitted from
Do not stare at operating lamp. May be harmful to the eyes.
Transportation
Keep the device in original or similar packaging while transporting
it.
System Security
The installer and user are responsible for password and security
configuration.
Maintenance
If the product does not work properly, please contact your dealer
or the nearest service center. We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance. A few device components (e.g., electrolytic
capacitor) require regular replacement. The average lifespan
varies, so periodic checking is recommended. Contact your dealer
for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside
surfaces of the product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device
lens is not exposed to the laser beam, or it may burn out. DO NOT
expose the device to high electromagnetic radiation or dusty
environments. For indoor-only device, place it in a dry and
well-ventilated environment. DO NOT aim the lens at the sun or
any other bright light. Make sure the running environment meets
the requirement of the device. DO NOT place the camera in
extremely hot, cold, dusty or damp locations, and do not expose it
to high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device, immediately turn
off the power, unplug the power cable, and contact the service
center.
Time Synchronization
Set up device time manually for the first time access if the local
time is not synchronized with that of the network. Visit the device
via Web browse/client software and go to time settings interface.
Reflection
Make sure that no reflective surface is too close to the device lens.
The IR light from the device may reflect back into the lens causing
reflection.
21
RISK GROUP 2
this product.
Français