Heating / Preheating; Freezing Protection; Radio/Cd/Aux - Sanotechnik SANOSPA XXL1908 Instructions Manual

will add 1 minute when pressing "
thecontinually when pressing the "
It will add 1 hour when pressing "
continually when pressing the "
you set up well of the start time , you could go on to the next step.
(3) Press "
minimum continue time is 5 minutes on the LCD, and this time will not flash. It will add 5
To activate a permanent filtering without a timeout, in active mode press "
minutes by pressing "
filtering begins the same as described above, but does not stop automatically.
please note that the maximum of continual time is 19 hours and 55 minutes. When you
set up well of the continual time , you could go on to the next step.
E.

HEATING / PREHEATING

(4) When everything is setting well, Press "
cleaning setting status with save.
You can also set this program to be active once a day or is active continuously. For the daily pre-
heating setting in passive mode press
NOTICE
The minimum heating time is 5 minutes and increases with each pressure of
1. all setting of Circulation-cleaning must be in Waitting mode status.
Press . Now you can set the heating time with the
MHz/CH
2. Circulation PUMP and OZONE are not working while all setting time.
SET
The maximum preheat time is 19 hours and 50 minutes! Press
c
to set the water temperature between 15 ° C and 42 ° C.
5. Pre-heating setting:
To exit this menu, press
Only one pre-heating setting is allowed each day. The LCD can show clearly in the following
settings will be saved. When you have saved the settings, "ON" appears on the screen. If you
figures about whether pre-heating setting status are ON or OFF.
pressed , "OFF" appears on the display.
PREHEAT
Fig.7: Pre-heat ON
When the time you set is displayed, the circular pump is switched on and the heating is turned on.
And it is not important if the pool is operating in an active or passive mode. Time is counting down
Pre-heating setting is in the "Waitting Mode" status and the LCD display "- - -".
on the screen till the end of heating. Heating is switched off as soon as the desired temperature
has been reached or when it has expired the time, set for heating. In the first 59 seconds the
(1) Press "
heating can not be switched off. After 1 minute you can switch off the heating by pressing
"PREHEAT" mark is flashed, In the same time, The Preheat start time setting is oning.
To set the uninterrupted heating without turning off, press
Press "
is switched on and is in operation together with a circular pump until the desired temperature is
reached. You can keep the temperature on the next way:
Set the temperature to 35 ° C. When the temperature drops to 34 ° C, the heating is switched on
together with the circular pump and heats water at 36 ° C and then switches off, etc. ...
F.

FREEZING PROTECTION

50
The massage pool has built-in protection against freezing. It is activated if the water temperature
falls below 5 ° C. Heating is switched on until 10 ° C is reached.
G.

RADIO/CD/AUX

In active mode, press
was curled and fastened in the hinge for transportation. Develop it and install it so that you will
have a good reception.
INSTRUCTION FOR USING THE SPA OUTDOORPOOL
" to continual working time setting of Circulation-cleaning, it will show the
" each time, And add 1 hour by pressing "
then press
PREHEAT
, so your settings will not be saved. But if you press
Fig.8: Pre-heat OFF
",and enter to Pre-heating setting status, "ON" of the LCD display, The
" again, The Preheat setting will quit in without save.
PROGRAMMING INSTRUCTIONS
to activate the radio. The antenna is located in the control box, which
" each time and the minutes could be added
" without stop. The adjustment range is 0~59.
" each time, and the hours could be added the
" without stop. The adjustment range is 0~23. When
", the system will quit the Circulation-
or
or
MHz/CH
SET
c
in active mode. Now the heating
". Process of
" each time.
to set the initial heating time.
for 10 minutes.
.
again. Now you can press
your
.
PREHEAT
53