Genie Z Series Wiring Diagram

GCL-MH
MEDIUM-DUTY HOIST OPERATOR
LINE IN
POWER CONNECTIONS
LINE IN
OPEN
POWER CONNECTIONS
L1/L1 N/L2
OPEN
L1/L1
N/L2
LINE
NEUTRAL
120V
(HOT)
LINE
240V LINE 1 LINE 2 NEUTRAL
120V
(HOT)
240V
LINE 1 LINE 2 GND
GND
OPEN
OPEN
CLOSE
CLOSE
STOP
STOP
3-BUTTON
STATION
3-BUTTON
STATION
HOI ST EXTERNAL
INTERLOCK INTERLOCK
HOI ST EXTERNAL
INTERLOCK INTERLOCK
ON ON
ON ON
OFF ON
OFF ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
WARNING: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE FUSES ONLY WITH THE SAME TYPE AND RATING
WARNING: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE FUSES ONLY WITH THE SAME TYPE AND RATING
www.GenieCompany.com/commercial
RADIO FUSE
©2012 The Genie Company
REPLACE RADIO
RADIO FUSE
FUSE WITH
GDC-315mA OR
REPLACE RADIO
NOT FOR RESIDENTIAL USE
NOT FOR RESIDENTIAL USE
CONTROL SIGNAL TERMINAL STRIP
CLASS 2 SUPPLY 20-40 VDC
CONTROL SIGNAL TERMINAL STRIP
CLOSE
STOP GND 1-BTN
CLASS 2 SUPPLY 20-40 VDC
CLOSE
STOP GND 1-BTN
1-BTN
STATION
N/O
1-BTN
STATION
REMOVE JUMPER
KEY
IF STOP BUTTON
N/O
SWITCH
IS USED
STATION
REMOVE JUMPER
N/O
KEY
IF STOP BUTTON
SWITCH
IS USED
STATION
CARD
N/O
READER
N/O
CARD
READER
O/C
MULTIPLE 3-BUTTON
N/O
PULL
STATION INSTALLATIONS
SWITCH
REQUIRE THE STOP
N/O
O/C
MULTIPLE 3-BUTTON
BUTTON TO BE WIRED
PULL
STATION INSTALLATIONS
SWITCH
IN SERIES
REQUIRE THE STOP
N/O
BUTTON TO BE WIRED
IN SERIES
SERIES II (STB) PHOTOCELLS
*
( CONNECT STB WIRES TO EITHER TERMINAL)
SERIES II (STB) PHOTOCELLS
*
( CONNECT STB WIRES TO EITHER TERMINAL)
TROUBLESHOOTING LED'S
24 VOLTS S T B
TROUBLESHOOTING LED'S
DC ENABLE
24 VOLTS S T B
OFF
DC ENABLE
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
ODC ODC N/O N/O EXT
STB STB SAFETY SAFETY INTLK
ODC ODC N/O N/O EXT
STB STB SAFETY SAFETY INTLK
REMOVE JUMPER
WHEN INSTALLING
EXTERNAL INTERLOCK
REMOVE JUMPER
WHEN INSTALLING
EXTERNAL INTERLOCK
SENSING EDGE SWITCH
SENSING EDGE SWITCH
*
*
I N D I C A T I O N
I N D I C A T I O N
STB DISABLED OR STB WIRING SHORT
STB DISABLED OR STB WIRING SHORT
STB ENABLED
STB ENABLED
NORMAL OPERATING CONDITION
HOIST INTERLOCK SWITCH OPEN:
NORMAL OPERATING CONDITION
1.) HOIST RELEASE NEEDS RESET.
HOIST INTERLOCK SWITCH OPEN:
2.) HOIST INTERLOCK CONNECTOR NOT PLUGGED IN.
1.) HOIST RELEASE NEEDS RESET.
3.) HOIST INTERLOCK DEFECTIVE.
2.) HOIST INTERLOCK CONNECTOR NOT PLUGGED IN.
EXTERNAL INTERLOCK OPEN
3.) HOIST INTERLOCK DEFECTIVE.
POWER SUPPLY PROBLEM:
EXTERNAL INTERLOCK OPEN
1.) CHECK AC POWER SUPPLY.
POWER SUPPLY PROBLEM:
2.) CHECK MAIN POWER FUSE.
1.) CHECK AC POWER SUPPLY.
3.) CHECK SECONDARY FUSE (2A)
2.) CHECK MAIN POWER FUSE.
3.) CHECK SECONDARY FUSE (2A)
| 800.843.4084
Wiring Diagram
PWR
20-40 VDC @ 300MA
MAX CURRENT
PWR
EXTERNAL RADIO TERMINAL STRIP
20-40 VDC @ 300MA
CLASS 2 SUPPLY 20-40 VDC
MAX CURRENT
EXT
INTLK PWR RAD GND
EXTERNAL RADIO TERMINAL STRIP
CLASS 2 SUPPLY 20-40 VDC
EXT
RAD GND
INTLK PWR
RELAY
NOM
GND
+ 24VDC
RADIO RELAY
NOM
GND
+ 24VDC
RADIO
+
+
-
-
+
+
-
-
THRU-BEAM
PHOTOCELLS
THRU-BEAM
PHOTOCELLS
SECONDARY
FUSE
SECONDARY
REPLACE SECONDARY
FUSE
FUSE WITH
GDB-2A OR
REPLACE SECONDARY