DEEP SEA ELECTRONICS DSE4610 Installation Instructions

CONFIGURATION PARAMETERS – MODULE (PAGE 1)
101 Contrast 0 (%) 117 RESERVED
102 Fast Loading Enabled On (1), Off (0) 118 RESERVED
103 All Warnings Latched On (1), Off (0) 119 RESERVED
104 Lamp Test At Startup On (1), Off (0) 120 CT Position
105 Power Save Mode Enable On (1), Off (0) 121 Generator Voltage Display
106 Deep Sleep Mode Enable On (1), Off (0) 122 Mains Voltage Display
107 Protected Start Enable On (1), Off (0) 123 Generator Frequency Display On (1), Off (0)
108 Event Log Display Format On (1), Off (0) 124 Mains Frequency Display
109 Power Up Mode 0 (Power Up Mode) 125 Current Display
110 RESERVED 126 kW Display
111 RESERVED 127 kVAr Display
Pin Protected
112 On (1), Off (0) 128 kVA Display
Maintenance Reset
113 Stop Button Cooldown On (1), Off (0) 129 pf Display
114 RESERVED 130 kWh Display
115 RESERVED 131 kVArh Display
116 RESERVED 132 kVAh Display
CONFIGURATION PARAMETERS – DIGITAL INPUTS (PAGE 3)
301 Digital Input A Source
302 Digital Input A Polarity
303 Digital Input A Action (If Source = User Config)
304 Digital Input A Arming (If Source = User Config)
305 Digital Input A Activation Delay (If Source = User Config)
306 Digital Input B Source
307 Digital Input B Polarity
308 Digital Input B Action (If Source = User Config)
309 Digital Input B Arming (If Source = User Config)
310 Digital Input B Activation Delay (If Source = User Config)
311 Digital Input C Source
312 Digital Input C Polarity
313 Digital Input C Action (If Source = User Config)
314 Digital Input C Arming (If Source = User Config)
315 Digital Input C Activation Delay (If Source = User Config)
316 Digital Input D Source
317 Digital Input D Polarity
318 Digital Input D Action (If Source = User Config)
319 Digital Input D Arming (If Source = User Config)
320 Digital Input D Activation Delay (If Source = User Config)
321-330 RESERVED
331 Analogue Input A (Set As Digital) Source
332 Analogue Input A (Set As Digital) Polarity
333 Analogue Input A (Set As Digital) Action (If Source = User Config)
334 Analogue Input A (Set As Digital) Arming (If Source = User Config)
335 Analogue Input A (Set As Digital) Activation Delay (If Source = User Config)
336 Analogue Input B (Set As Digital) Source
337 Analogue Input B (Set As Digital) Polarity
338 Analogue Input B (Set As Digital) Action (If Source = User Config)
339 Analogue Input B (Set As Digital) Arming (If Source = User Config)
340 Analogue Input B (Set As Digital) Activation Delay (If Source = User Config)
341 Analogue Input C (Set As Digital) Source
342 Analogue Input C (Set As Digital) Polarity
343 Analogue Input C (Set As Digital) Action (If Source = User Config)
344 Analogue Input C (Set As Digital) Arming (If Source = User Config)
345 Analogue Input C (Set As Digital) Activation Delay (If Source = User Config)
PRESSURE SENSOR LIST TEMPERATURE SENOR LIST
Index Type Index Type
0 Not used 0 Not Used
1 Dig Closed for Alarm 1 Dig Closed for Alarm
2 Dig Open for Alarm 2 Dig Open for Alarm
3 VDO 5 Bar 3 VDO 120 °C
4 VDO 10 Bar 4 Datcon High
5 Datcon 5 Bar 5 Datcon Low
6 Datcon 10 Bar 6 Murphy
7 Datcon 7 Bar 7 Cummins
8 Murphy 7 Bar 8 PT100
9 CMB812 9 Veglia
10 Veglia 10 Beru
11 User Defined 11 User Defined
CONFIGURATION PARAMETERS – OUTPUTS (PAGE 4)
401 Digital Output A Source
402 Digital Output A Polarity
403 Digital Output B Source
Gen (0), Load(1) 404 Digital Output B Polarity
On (1), Off (0) 405 Digital Output C Source
On (1), Off (0) 406 Digital Output C Polarity
CONFIGURATION PARAMETERS – TIMERS (PAGE 5)
On (1), Off (0)
501 Mains Transient Delay
On (1), Off (0)
502 Start Delay
On (1), Off (0)
503 Preheat Timer
On (1), Off (0)
504 Crank Time
505 Crank Rest Time
On (1), Off (0)
506 Smoke Limiting
On (1), Off (0)
507 Smoke Limiting Off
On (1), Off (0)
508 Safety On Delay
On (1), Off (0)
509 Warm Up Time
On (1), Off (0)
CONFIGURATION PARAMETERS – GENERATOR (PAGE 6)
601 Alternator Fitted
0 (Input Source)
602 Alternator Poles
0 (Polarity)
603 Under Voltage Shutdown Enable On (1), Off (0)
0 (Action)
604 Under Voltage Trip Shutdown
0 (Arming)
605 Under Voltage Warning Enable
0 s
606 Under Voltage Warning Trip
0 (Input Source)
607 RESERVED
0 (Polarity)
608 Loading Voltage
0 (Action)
609 Over Voltage Warning Enable
0 (Arming)
610 Over Voltage Warning Return
0 s
0 (Input Source)
611 Over Voltage Warning Trip
0 (Polarity)
612 Over Voltage Shutdown Trip
0 (Action)
Under Frequency Shutdown
613
0 (Arming)
Enable
0 s
614 Under Frequency Shutdown Trip 0.0 Hz
0 (Input Source)
Under Frequency Warning
615
0 (Polarity)
Enable
0 (Action)
616 Under Frequency Warning Trip
0 (Arming)
617 RESERVED
0 s
618 Loading Frequency
619 Nominal Frequency
0 (Input Source)
CONFIGURATION PARAMETERS – MAINS (PAGE 7)
0 (Polarity)
701 AC System
0 (Action)
702 Mains Failure Detection
0 (Arming)
703 Immediate Mains Dropout
0 s
704 Under Voltage Enable
0 (Input Source)
705 Under Voltage Level
0 (Polarity)
706 Under Voltage Return
0 (Action)
707 Over Voltage Enable
0 (Arming)
708 Over Voltage Return
0 s
CONFIGURATION PARAMETERS – ENGINE (PAGE 8)
0 (Input Source)
801 Start Attempts
0 (Polarity)
802 Over Speed Overshoot
0 (Action)
803 Over Speed Delay
0 (Arming)
Gas Choke Timer
0 s
804
(Gas Engine Only)
PERCENTAGE SENSOR LIST
Gas On Delay
805
Index Type
(Gas Engine Only)
0 Not Used
Gas Ignition Off Delay
806
1 Dig Closed for Alarm
(Gas Engine Only)
2 Dig Open for Alarm
Crank Disconnect On Oil
807
3 VDO Ohm (10-180) Pressure Enable
4 VDO Tube (90-0)
Check Oil Pressure Prior To
808
5 US Ohm (240-33) Starting
809 Crank Disconnect On Oil
6 GM Ohm (0-90)
7 GM Ohm (0-30) 810 Crank Disconnect On Frequency 0.0 Hz
8 Ford (73-10) Crank Disconnect On Engine
811
Speed
9 User Defined
812 Under Speed Enable
813 Under Speed Trip
814 Over Speed Trip
815 Low Battery Voltage Enable
816 Low Battery Voltage Trip
817 Low Battery Voltage Return
x Functionality in DSE4610 & DSE4620
x Functionality in DSE4620 only
0 (Output Source) 407 Digital Output D Source 0 (Output Source)
0 (Output Polarity) 408 Digital Output D Polarity 0 (Output Polarity)
0 (Output Source) 409 Digital Output E Source 0 (Output Source)
0 (Output Polarity) 410 Digital Output E Polarity 0 (Output Polarity)
0 (Output Source) 411 Digital Output F Source 0 (Output Source)
0 (Output Polarity) 412 Digital Output F Polarity 0 (Output Polarity)
510 Return Delay 519 Delayed Load Output 2
511 Cooling Time 520 Delayed Load Output 3
512 ETS Solenoid Hold 521 Delayed Load Output 4
513 Failed To Stop Delay 522 Power Save Mode Delay
514 Generator Transient Delay 523 Deep Sleep Mode Delay
515 Transfer Time 524 Page Timer
516 Breaker Trip Pulse 525 Cooling Time at Idle
517 Breaker Close Pulse
518 Delayed Load Output 1
On (1), Off (0) 620 Over Frequency Warning Enable On (1), Off (0)
0 621 Over Frequency Warning Return 0.0 Hz
622 Over Frequency Warning Trip 0.0 Hz
0 V 623 Over Frequency Shutdown Enable On (1), Off (0)
On (1), Off (0) 624 Over Frequency Shutdown Trip 0.0 Hz
0 V 625 AC System 0 (Ac System)
626 CT Primary 0 A
0 V 627 Full Load Rating 0 A
On (1), Off (0) 628 Immediate Over Current Enable On (1), Off (0)
Delayed Over Current Alarm
0 V 629 On (1), Off (0)
Enable
0 V 630 Delayed Over Current Alarm Action 0 (Action)
0 V 631 Over Current Delay Time 0 s
On (1), Off (0) 632 Over Current Trip 0 %
633 kW Rating 0 kW
On (1), Off (0) 634 Over kW Protection Enable On (1), Off (0)
0.0 Hz 635 Over kW Protection Action 0 (Action)
636 Over kW Protection Trip 0 %
0.0 Hz 637 Over kW Protection Trip Delay 0 s
0.0 Hz
0 (AC System) 709 Over Voltage Level Trip 0 V
On (1), Off (0) 710 Under Frequency Enable On (1), Off (0)
On (1), Off (0) 711 Under Frequency Trip 0.0 Hz
On (1), Off (0) 712 Under Frequency Return 0.0 Hz
0 V 713 Over Frequency Enable On (1), Off (0)
0 V 714 Over Frequency Return 0 Hz
On (1), Off (0) 715 Over Frequency Trip 0.0 Hz
0 V
0 818 Low Battery Voltage Delay 0:00:00
0 % 819 High Battery Voltage Enable On (1), Off (0)
0 s 820 High Battery Voltage Return 0.0 V
0 s 821 High Battery Voltage Trip 0.0 V
High Battery Voltage Warning
0 s 822 0 s
Delay
0 s 823 Charge Alt Shutdown Enable On (1), Off (0)
On (1), Off (0) 824 Charge Alt Shutdown Trip 0.0 V
On (1), Off (0) 825 Charge Alt Shutdown Delay 0 s
0.00 Bar 826 Charge Alt Warning Enable On (1), Off (0)
827 Charge Alt Warning Trip 0.0 V
0 RPM 828 Charge Alt Warning Delay 0 s
On (1), Off (0) 829 Low Battery Start Arming On (1), Off (0)
0 RPM 830 Low Battery Start Threshold 0.0 V
0 RPM 831 Low Battery Start Delay 0 s
On (1), Off (0) 832 Low Battery Start Run Time 0 s
0.0 V 833 Magnetic Pickup Fitted On (1), Off (0)
0.0 V 834 Flywheel Teeth 0
CONFIGURATION PARAMETERS – ANALOGUE INPUTS (PAGE 9)
901 Analogue Input A Senor Type 0 (Sensor Type)
902 Analogue Input A Sensor Selection 0 (Pressure Sensor List)
903 Low Oil Pressure Enable On (1), Off (0)
904 Low Oil Pressure Trip 0 Bar
905 Oil Pressure Sender Open Circuit On (1), Off (0)
906 Analogue Input B Senor Type 0 (Sensor Type)
907 Analogue Input B Sensor Selection 0 (Temperature Sensor List)
908 High Engine Temperature Trip 0.00 °C
909 Temperature Sender Open Circuit On (1), Off (0)
910 Analogue Input C Sensor Usage Flexible Sensor (1), Fuel Level Sensor (0)
911 Analogue Input C Senor Type 0 (Sensor Type)
912 Analogue Input C Sensor Selection 0 (Pressure / Temperature / Percentage Sensor List)
913 Flexible Sensor C Arming 0 (Arming)
914 Flexible Sensor C Low Alarm Action 0 (Action)
915 Flexible Sensor C Low Alarm Trip 0 % / Bar / °C
916 RESERVED
917 Flexible Sensor C Low Pre-Alarm Enable On (1), Off (0)
918 Flexible Sensor C Low Pre-Alarm Trip 0 % / Bar / °C
919 Flexible Sensor C Low Pre-Alarm Return 0 % / Bar / °C
920 RESERVED
921 Flexible Sensor C High Pre-Alarm Enable On (1), Off (0)
922 Flexible Sensor C High Pre-Alarm Return 0 % / Bar / °C
923 Flexible Sensor C High Pre-Alarm Trip 0 % / Bar / °C
924-925 RESERVED
926 Flexible Sensor C High Alarm Action 0 (Action)
927 Flexible Sensor C High Alarm Trip 0 % / Bar / °C
928-929 RESERVED
930 Fuel Sensor C Low Shutdown Enable On (1), Off (0)
931 Fuel Sensor C Low Shutdown Trip 0 %
932 Fuel Sensor C Low Shutdown Delay 0 s
933 Fuel Sensor C Low Pre-Alarm Enable On (1), Off (0)
934 Fuel Sensor C Low Pre-Alarm Trip 0 %
935 Fuel Sensor C Low Pre-Alarm Return 0 %
936 Fuel Sensor C Low Pre-Alarm Delay 0 s
937 Fuel Sensor C High Pre-Alarm Enable On (1), Off (0)
938 Fuel Sensor C High Pre-Alarm Return 0 %
939 Fuel Sensor C High Pre-Alarm Trip 0 %
940 Fuel Sensor C High Pre Alarm Delay 0 s
941 RESERVED
942 Fuel Sensor C High Alarm Action 0 (Action)
943 Fuel Sensor C High Alarm Trip 0 %
944 Fuel Sensor C High Alarm Delay 0 s
CONFIGURATION PARAMETERS – SCHEDULER (PAGE 10)
1001 Enable Scheduler
1002 Schedule Run On or Off Load
1003 Scheduler Period
1004, 1008, 1012, 1016, 1020, 1024, 1028, 1032 Start Time (Entry 1-8)
1005, 1009, 1013, 1017, 1021, 1025, 1029, 1033 Day (Entry 1-8)
1006, 1010, 1014, 1018, 1022, 1026, 1030, 1034 Week (Entry 1-8)
1007, 1011, 1015, 1019, 1023, 1027, 1031, 1035 Duration (Entry 1-8)
CONFIGURATION PARAMETERS – TIME (PAGE 11)
1101 Time of Day 0:00:00 1103 Week of Year
1102 Day of Week 0 (1=Monday)
CONFIGURATION PARAMETERS – MAINTENANCE ALARMS (PAGE 12)
Air Maintenance Alarm Engine
1201 Oil Maintenance Alarm Enable On (1), Off (0) 1206
Hours
1202 Oil Maintenance Alarm Action 0 (Action) 1207 Fuel Maintenance Alarm Enable On (1), Off (0)
Oil Maintenance Alarm Engine
1203 0 h 1208 Fuel Maintenance Alarm Action 0 (Action)
Hours
Fuel Maintenance Alarm Engine
1204 Air Maintenance Alarm Enable On (1), Off (0) 1209
Hours
1205 Air Maintenance Alarm Action 0 (Action)
DIGITAL INPUT ALARM
SENSOR TYPE AC SYSTEM
ARMING
Index Type Index Type Index Arming
0 None 0 2 Phase 3 Wire (L1-L2) 0
1 Digital Input 1 2 Phase 3 Wire (L1-L3) 1
2 Percentage Sensor 2 3 Phase 3 Wire 2
3 Pressure Sensor 3 3 Phase 4 Wire 3
4 Temperature Sensor 4 3 Phase 4 Wire (Delta)
5 Single Phase 2 Wire
On (1), Off (0)
On (1), Off (0)
Weekly(0), Monthly(1)
0:00:00
0 (1=Monday)
1, 2, 3 or 4
0 s
1-52
0 h
0 h
POWER UP
MODE
Index Mode
Always 0 Stop
From Safety On 1 Manual
From Starting 2 Auto
Never