Fcc Statement; Safety Notices - TP-Link TL-SG1008D User Manual

8 7 6 5 4 3 2 1
Figure 3-2 TL-SG1008D Switch Rear Panel sketch
3.3 LED indicators
The LED indicators include Power LED and Link/Act LEDs (See
LED indicators are used for monitoring and troubleshooting of the Switch. The
following section shows the LED indicators for the Switch along with an explanation
of each indicator.
Ø Power LED: This indicator will light up when the Switch powers up. If the LED
is not lit, please check the power adapter and connection.
1000M LINK/ACT LEDs: These LEDs indicate Link/Active status. One LED will
Ø
light green when a 1000Mbps device is connected to the corresponding port. It
flashes when data is being transmitted or received on the connection.
Ø 10/100M LINK/ACT LEDs: These LEDs indicate Link/Active status. One LED
will light green when a 10Mbps or 100Mbps device is connected to the
corresponding port. It flashes when data is being transmitted or received on the
connection.
Appendix A: Specifications
General
Standards IEEE802.3 , IEEE802.3u , IEEE802.3ab
Topology Star
Protocol CSMA/CD
Data Transfer Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)
Rate Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
Network Media 10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
(Cable) EIA/TIA-568 100Ù STP (maximum 100m)
100Base-Tx: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ù STP (maximum 100m)
1000Base-T: UTP category 5, 5e cable (maximum 100m)
Number of Ports 5/8 10/100/1000Mbps Auto-Negotiation ports
LED indicators Power, Link/Act
Transfer Method Store-and-Forward
MAC Address Learning Automatically learning, automatically Update
Frame Filter Rate 10Base-T: 14880pps/Port
100Base-Tx: 148800pps/Port
1000Base-T: 1488000pps/Port
Frame Forward Rate 10Base-T: 14880pps/Port
100Base-Tx: 148800pps/Port
1000Base-T: 1488000pps/Port
2
Dimensions(
W D H
POWER
Power Supply Output:
Operating Temperature
Storage Temperature
Operating Humidity
Storage humidity
Figure 3-1 ). The
Appendix B: Troubleshooting
1. The Power LED is not lit
Ø Make sure the AC power Adapter is plugged into an outlet properly and it's
connector is plugged into the power jack of the switch .
Ø Make sure the power source is ON.
Ø Make sure you are using the TP-LINK power adapter supplied with your switch.
2. The Link/Act LED is not lit when a device is connected
to the corresponding port
Ø Make sure that the cable connectors are firmly plugged into the Switch and the
device.
Ø Make sure the connected device is turned on and its adapter is installed
correctly and is working.
Ø The cable must be less than 100 meters long(328 feet).
Appendix C: Contact Information
For help with the installation or operation of the TP-LINK TL-SG1005D/TL-
SG1008D Switch, please contact us.
E-mail: support@tp-link.com
Website: http://www.tp-link.com
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice.
trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or
used to make any derivative such as translation, transformation, or adaptation
without permission from TP-LINK Technologies Co., Ltd. Copyright
Technologies Co., Ltd. All rights reserved.
71030478
Rev: 2.0
Environmental and Physical
) 7.3 5.7 1.7 in. (186mm 146mm 44mm)
AC 9V~ 1.2A
O O O O
0 C~40 C (32 F~104 F)
O O O O
-40 C~70 C (-40 F~158 F)
10%~90% non-condensing
5%~95% non-condensing
is a registered
2005 TP-LINK
3

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Ø Reorient or relocate the receiving antenna.
Ø Increase the separation between the equipment and receiver.
Ø Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Ø Consult the dealer or an experienced radio/TV technician for help.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/
EEC, this product meets the requirements of the following standards:
EN55022
Ø
Ø EN55024
Ø EN60950

SAFETY NOTICES

Caution:
Do not use this product near water, for example, in a wet basement or near a
swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
4