DeLonghi HCX9115E-6A AG Instructions For Use Manual page 6

stand the power consumption (Watt) indicated by the
labelling.
- If more than one appliance is used at once, it is
important to ensure that the electric plant is able to
support the power required.
Mounting the feet
Turn the appliance upside down on a rug or soft surface in
order to prevent damaging the paint finish.
Fix the feet to the appliance with the nr. 4 screws 4.8x13 PH
G supplied (see fig. 1), 2 screws for each foot.
Wall-Mounting Installation
The wall mounting kit contains:
4 metal brackets (H)
4 screws 4.5x25PH (I)
2 butterfly screws M5 (J)
4 plastic anchors 6x30 (K)
Required tools for assembly and estimated assembly
time
Drill
Screwdriver PH 2 x 100 (Phillips type)
Estimated assembly time: 30 minutes
Before installing the unit , make sure of the following:
The appliance must not be located directly
-
beneath a current outlet.
- The plug and outlet must be easy to reach after
installation.
- No electric cables or other pipes could be
damaged during the installation.
Keep away from curtains or flammable materials.
-
To wall-mount, proceed as follows:
Turn the appliance upside down on a flat stable surface. Fix
the 2 brackets H with the 2 butterfly screws J as shown in
Fig. 2. For brick walls use a 6 mm concrete drill bit. For plaster
board or drywall, it is recommended to use appropriate
screws and anchors (not supplied).
- Before drilling the wall, mark the exact points,
respecting the minimum distances as shown in fig. 3.
- Drill the wall where previously marked, and insert the
plastic anchors K.
Fix the 2 metal brackets H using the two screws I
-
provided.
- Hang the appliance on the bracket.
- Mark out the 2 lower fixing points. Remove the
appliance, drill the lower holes and insert the wall
anchors K.
- Now, you can hang back the heater on the bracket and
fix the lower part of the appliance with the 2 remaining
screws I.
USE
Operation and use
- Plug into the outlet socket.
- The appliance emits a beep. The power indicator light
(A) comes on and remains lit while the appliance is
powered.
- The appliance switches to stand-by.
- Press the ON/OFF (B) to turn the appliance on. It begins
heating the room according to the current settings.
- Press the MODE (D) button to select one of the following
operating modes:
- Freeze prevention
In this mode, the appliance keeps the room at a
temperature of 45°F (7°C) to avoid freezing.
Heating 1, 2, 3 and Heating 3 + Fan
-
In this mode, the desired temperature can be selected by
pressing the adjustment buttons + and –. By pushing
the + or - button once, the temperature (shown on the
display) will increase or decrease by 1 degree.
Heating 1
The appliance operates at low power.
Heating 2
The appliance operates at medium power.
Heating 3
The appliance operates at high power.
Heating 3 + Fan
The appliance operates at the maximum power with
the fan. The setting temperature range available is from
61°F to 90°F (16°C to 32°C).
"ECO plus" function
The "ECO plus" function is available in Heating 1, 2 3 and
3 + fan modes only. To activate the function, press the
"ECO plus" (E) button. When this function is active the
appliance automatically sets the most appropriate power
level to guarantee optimum comfort while reducing energy
consumption. While the "ECO plus" function is active, the
appliance may switch automatically to a lower heating power
than the one displayed.
Working indicator
The symbol indicates the heating status by means of its
colors.
RED: the unit is heating at the maximum power.
6