Table of Contents
Advertisement
Quick Links
240 VAC POWER SUPPLY
MULTI POSITION
INSTALLER / SERVICE TECHNICIAN:
USE THE INFORMATION IN THIS MANUAL FOR THE INSTALLATION AND
SERVICING OF THE FURNACE AND KEEP THE DOCUMENT NEAR THE
UNIT FOR FUTURE REFERENCE.
HOMEOWNER:
PLEASE KEEP THIS MANUAL NEAR THE FURNACE FOR FUTURE
REFERENCE.
Printed in Canada
Printed on 100% recycled paper
2012-10-15
Models:
SUP10-M2301C
SUP15-M2301C
SUP18-M2301C
SUP20-M2301C
SUP23-M2301C
SUP20-M2301D
SUP23-M2301D
SUP27-M2301D
Caution: Do not tamper with
the unit or its controls. Call a
qualified service technician.
Manufactured by:
Industries Dettson inc.
3400 Industrial Boulevard
Sherbrooke, Quebec - Canada
J1L 1V8
X40209 Rev. C
Advertisement
Table of Contents
Related Manuals for SUPREME SUP10-M2301C
Summary of Contents for SUPREME SUP10-M2301C
- Page 1 240 VAC POWER SUPPLY Models: MULTI POSITION SUP10-M2301C SUP15-M2301C SUP18-M2301C SUP20-M2301C SUP23-M2301C SUP20-M2301D SUP23-M2301D SUP27-M2301D Caution: Do not tamper with INSTALLER / SERVICE TECHNICIAN: the unit or its controls. Call a qualified service technician. USE THE INFORMATION IN THIS MANUAL FOR THE INSTALLATION AND...
-
Page 2: Table Of Contents
DANGER, WARNING AND CAUTION....3 Table 3 : Technical specifications........10 IMPORTANT INFORMATION ........ 3 Table 4 : Airflow (CFM) - SUPREME with 1/3HP motor..10 DANGER OF FREEZING ........3 Table 5 : Airlfow (CFM) - SUPREME with 1HP motor..10 INSTALLATION............. 3 Table 6 : PARTS LIST, Supreme with POSITIONING THE FURNACE...... -
Page 3: Safety
Ask the technician installing your furnace to show SAFETY and explain to you the following items: The main disconnect switch or circuit breaker; DANGER, WARNING AND CAUTION The air filter and how to change it (check The words DANGER, WARNING and CAUTION are used to monthly and clean or replace if necessary);... -
Page 4: Positioning The Furnace
same position to insure uniform air distribution through the with it. It is also recommended to install the blower door elements. before handling or moving the unit. Refer to Figure 1 for additional details. POSITIONING THE FURNACE Figure 1: Upflow installation WARNING Fire and explosion hazard. -
Page 5: Electrical System
Once the current has stabilized, a reading should be taken and the anticipator adjusted to that value. The SUPREME furnace is completely pre-wired and all field longer heating cycles are desired, the anticipator can be wiring must be connected to the terminal blocks on the unit. -
Page 6: Ducts And Filters
HIGH If the heating and air-cooling speed are the same, the The SUPREME furnace is equipped with a filter frame for the orange wire and the blue wire can be connected on the blower compartment. It must be installed on the outside of same terminal on the motor. -
Page 7: Use Of A Heat Pump
during a call for heat. Refer to the wiring diagrams for the location of the relay (RAcc) on the control panel. Figure 8 : Manual Furnace Controls 2.7.2. Use of a heat pump When using a heat pump, a thermostat with dial fuel option or a fossil fuel kit is required that prevents the operation of the electric elements and the heat pump at the same time. -
Page 8: Supply Air Temperature Rise Test
3.4.2. High limit verification 0.82 x amps. x volts After operating the furnace for at least 15 minutes, restrict Liter/s= ------------------------- the return air supply by blocking the filters or the return air Diff. temperature ˚C register and allow the furnace to shut off on High Limit. The electric heaters must deactivate themselves one by one 3.1 x amps. -
Page 9: Furnace Information
FURNACE INFORMATION Model: Serial number: Furnace installation date: Service telephone # - Day: Night: Dealer name and address: START-UP RESULTS Voltage: Total current consumed by the elements: Supply air temperature: Return air temperature: Supply air duct static pressure: Return air duct static pressure: Total pressure: Calculated air flow: Current consumed by the blower motor:... -
Page 10: Table 3 : Technical Specifications
3 tons 5 tons 1) Select a blower speed that will generate the specified temperature rise 2) Calculated on the basis of Norm C22.2 Nr. 236 Table 4 : Airflow (CFM) - SUPREME with 1/3HP motor Static Pressure Blower Speed MED-LOW... -
Page 11: Figure 9 : Furnace Dimensions
Figure 9 : Furnace dimensions... -
Page 12: Figure 10 : Wiring Diagram
Figure 10 : Wiring diagram... -
Page 13: Figure 11 : Parts List, Supreme With
Figure 11 : PARTS LIST, Supreme with 1/3 HP and 1 HP motor: SUPxx-M2301C or SUPxx-M2301D B50131A.dwg... -
Page 14: Table 6 : Parts List, Supreme With
Table 6: PARTS LIST, Supreme with 1/3 HP and 1 HP motor: SUPxx-M2301C or SUPxx-M2301D ITEM PART # DESCRIPTION COMMENTS B04114-01 HEATING ELEMENT PLATE ASSEMBLY SUP10kw (1/3 HP) Item 12 included B04115-01 HEATING ELEMENT PLATE ASSEMBLY SUP15kw (1/3 HP) Item 12 included...
Need help?
Do you have a question about the SUP10-M2301C and is the answer not in the manual?
Questions and answers