Fujitsu AirStage AS A014GCEH Series Installation Manual

Fujitsu AirStage AS A014GCEH Series Installation Manual

Indoor unit (wall mounted type)
Hide thumbs Also See for AirStage AS A014GCEH Series:

Advertisement

Quick Links

EEV internal model
AS*A012GCEH
AS*A014GCEH
EEV external model
AS*E012GCEH
AS*E014GCEH
Refer to the rating label for the serial number, manufactured
year and month.
TM
INSTALLATION MANUAL
INSTALLATIONSANLEITUNG
MANUEL D'INSTALLATION
UNITÉ INTÉRIEURE (Type montage mural)
MANUAL DE INSTALACIÓN
UNIDAD INTERIOR (Tipo montado en pared)
Únicamente para personal de servicio autorizado.
MANUALE DI INSTALLAZIONE
UNITÀ INTERNA (tipo montato a parete)
A uso esclusivo del personale tecnico autorizzato.
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ
ΕΣΩΤΕΡΙΚΗ ΜΟΝΑΔΑ (Επιτοιχιος Τύπος)
Μόνο για εξουσιοδοτημένο τεχνικό προσωπικό.
MANUAL DE INSTALAÇÃO
РУКОВОДСТВО ПО УСТАНОВКЕ
ВНУТРЕННИЙ МОДУЛЬ (настенного типа)
Только для авторизованного обслуживающего персонала.
INDOOR UNIT (Wall Mounted Type)
For authorized service personnel only.
INNENGERÄT (wandmontierter Typ)
Nur für autorisiertes Fachpersonal.
Pour le personnel agréé uniquement.
UNIDADE INTERIOR (Tipo mural)
Apenas para técnicos autorizados.
MONTAJ KILAVUZU
İÇ ÜNİTE (Duvara Monteli Tip)
Yalnızca yetkili servis personeli için.
[Original instructions]
PART No. 9373370468
MADE IN P.R.C.

Advertisement

Table of Contents
loading

Summary of Contents for Fujitsu AirStage AS A014GCEH Series

  • Page 1 INSTALLATION MANUAL INDOOR UNIT (Wall Mounted Type) For authorized service personnel only. INSTALLATIONSANLEITUNG INNENGERÄT (wandmontierter Typ) Nur für autorisiertes Fachpersonal. MANUEL D’INSTALLATION EEV internal model UNITÉ INTÉRIEURE (Type montage mural) AS*A012GCEH Pour le personnel agréé uniquement. AS*A014GCEH MANUAL DE INSTALACIÓN EEV external model UNIDAD INTERIOR (Tipo montado en pared) AS*E012GCEH...
  • Page 2: Table Of Contents

    INSTALLATION MANUAL This mark indicates procedures which, if improperly performed, CAUTION PART No. 9373370468 might possibly result in personal harm to the user, or damage VRF system indoor unit (Wall mounted type) to property. Read carefully all security information before use or install the air conditioner. Do not attempt to install the air conditioner or a part of the air conditioner by yourself.
  • Page 3: Accessories

    2.3. Accessories 3. INSTALLATION WORK Correct initial installation location is important because it is difficult to move unit after it is installed. WARNING 3.1. Selecting an installation location For installation purposes, be sure to use the parts supplied by the manufacturer or other prescribed parts.
  • Page 4: Installation Dimension

    3.3.3 Cutting the hole in the wall for the connecting piping 3.2. Installation dimension (1) Cut a hole in the wall at the posi- Wall hook bracket tion shown in the following. Unit: mm Center mark Center mark (2) Cut the hole so that the outside end is lower (5 to 10 mm) than the inside end.
  • Page 5: Pipe Installation

    Installing the drain cap 4.2. Pipe requirement Use a hexagonal wrench 4 mm at opposite side to No gap insert the drain cap, till the drain cap contacts the tip of drain cock. CAUTION Hexagonal Drain cock wrench Drain cap Refer to the installation manual for the outdoor unit for description of allowable pipe length and height difference.
  • Page 6: Electrical Wiring

    4.3.3 Pipe connection CAUTION When the flare nut is tightened properly by your hand, hold the body side coupling with a Earth (Ground) the unit. separate spanner, then tighten with a torque wrench. Do not connect the earth (ground) cable to a gas pipe, water pipe, lightning rod, or a telephone earth (ground) cable.
  • Page 7: Wiring Method

    B. For strand wiring 5.2. Wiring method (1) Use ring terminals with insulating sleeves as shown in the figure below to connect to the terminal block. Example (2) Securely clamp the ring terminals to the cables using an appropriate tool so that the Outdoor unit or RB unit *1 cables do not come loose.
  • Page 8: Wiring

    • Position and detail of the switches 5.4. Wiring You need to remove the front panel. Refer to (1) Open the intake grille. Refer to “8. FRONT “8. FRONT PANEL RE- For refrigerant PANEL REMOVAL AND INSTALLATION”. Cable clamp MOVAL AND INSTAL- circuit address (2) Remove the wire cover and remove the LATION”.
  • Page 9: Function Setting

    • Custom code setting for indoor unit Function Function Setting number Default Details number Set the DIP switch SET3 SW1, 2, referring to the figure and table below. Forced ther- DIP switch “SET3” mostat off Switching Setting is required when connecting function for (Forbidden) a refrigerant-leak detecting device.
  • Page 10: Optional Parts Wiring

    6.3.2 Checking the function settings Name Application Press and hold the “MANUAL AUTO” button on the indoor unit for 3 seconds to check CNA01 Apply voltage terminal For external input the function settings. It is necessary to disconnect the power in order to return to normal CNA03 operation mode.
  • Page 11 NOTE : DC power supply P.C.B 12 to 24V When connected to multiple indoor units directly, it will cause breakdown. Load Operation behavior resistance CNA01 ● Input signal type Edge The input signal type can be selected. It is switched by DIP switch on the indoor unit PCB. Load DIP switch [SET2 SW2] Input signal type...
  • Page 12: Finishing

    6.5.2 External output • Bind the connection cable with Connection cable (Power supply cable) vinyl tape. • A twisted pair cable (22AWG) should be used. Maximum length of cable is 25m. • Bundle the piping and drain hose • Use an external input and output cable with appropriate external dimension, depending together by wrapping them with on the number of cables to be installed.
  • Page 13: Front Panel Installation

    8.3. Front panel installation 11. ERROR CODES If you use a wired type remote controller, error codes will appear on the remote controller (1) First, fit the lower part of the front panel, and insert top and bottom hooks. (3 top display.

Table of Contents