UCL SWIFT TEK-1 Training Manual page 39

Hide thumbs

Table of Contents

Referencing Setup

The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use

The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection

The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use

The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection

REFERENCING SETUP

an inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP

The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use

scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.

an inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP

scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.

460 and DLS 350. Plug the loopback adapter on to the paired LC side of the Test Jumper. The RP 460

an inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP

The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use an

The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm

460 and DLS 350. Plug the loopback adapter on to the paired LC side of the Test Jumper. The RP 460

The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm

should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button

460 and DLS 350. Plug the loopback adapter on to the paired LC side of the Test Jumper. The RP 460

inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the OPM1 and LSMM.

button once to put it into the dBm mode.

should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button

once to put it into the dBm mode.

should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button

Plug the loopback adapter on to the paired LC side of the Test Jumper. The OPM1 should be in the dBm

once to put it into the dBm mode.

measurement mode. If it is not in the dBm mode, press the dB/dBm button once to put it into the dBm mode.

Setting Reference

SETTING REFERENCE

Setting Reference

The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm

The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm

The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm

The LSMM output power is calibrated to -22dBm. If the OPM1 screen displays between -22.00dBm and

and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm

and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

-25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the dB/dBm button. The

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

OPM1 screen will display 0.00dB, with some minor variation. DO NOT switch the OPM1 back to the dBm mode.

RP 460 back to the dBm mode.

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

RP 460 back to the dBm mode.

Between -22 and -25dBm

Between -5.00 and -7.00dBm

Between -22 and -25dBm

Loss Test

LOSS TEST

Loss Test

The paired Test Jumper MUST remain attached to the DLS 350 and RP 460. Do not remove the Test

The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the

The paired Test Jumper MUST remain attached to the DLS 350 and RP 460. Do not remove the Test

The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the

The paired Test Jumper MUST remain attached to the LSMM and OPM1. Do not remove the Test Jumper from

Jumper from the optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be

The paired Test Jumper MUST remain attached to the DLS 350 and RP 460. Do not remove the Test

optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to

Jumper from the optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be

the optical link. The connectors on the Test Jumper and the fiber-under-test should be cleaned to appropriate

cleaned to appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped

Jumper from the optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be

appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper

cleaned to appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped

standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped LC end of the Test Jumper into

LC end of the Test Jumper into one end of the Fiber-Under-Test using the bulkhead as shown. Plug

cleaned to appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped

into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the

LC end of the Test Jumper into one end of the Fiber-Under-Test using the bulkhead as shown. Plug

one end of the fiber-under-test using the bulkhead as shown. Plug the loopback on to the other end of the

the loopback on to the other end of the Fiber-Under-Test. The Insertion Loss of the Fiber-Under-Test

LC end of the Test Jumper into one end of the Fiber-Under-Test using the bulkhead as shown. Plug

Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be

the loopback on to the other end of the Fiber-Under-Test. The Insertion Loss of the Fiber-Under-Test

fiber-under-test. The Insertion Loss of the fiber-under-test will be shown on the OPM1 screen.

will be shown on the RP 460 screen.

the loopback on to the other end of the Fiber-Under-Test. The Insertion Loss of the Fiber-Under-Test

shown on the RP 460 screen.

will be shown on the RP 460 screen.

Test Jumper

DMT

3330 Earhart Drive, Suite 208

DMT

Paired Test Jumper

Hold for 5 seconds

Fiber-Under-Test

Carrollton, TX 75006

Office: 972.556.0916

Loopback Adapter

M-UM038-01 RP 460 Reference and Test

Fax: 972.910.8384

M-UM038-01 RP 460 Reference and Test

Reference is set

Loopback

M-UM038-01 RP 460 Reference and Test

OPM1

Page 12

Page 4

Page 12

PAGE 11

Page 12

Table of Contents

UCL SWIFT TEK-1 Training Manual page 39

Related Manuals for UCL SWIFT TEK-1

Related Products for UCL SWIFT TEK-1

Table of Contents