Table of Contents
Advertisement
Referencing Setup
Referencing Setup
Referencing Setup
Referencing Setup
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection
REFERENCING SETUP
Referencing Setup
The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use
scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.
scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.
scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.
The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use
The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use an
an inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP
The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm
The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm
The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm
an inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP
inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the OPM1 and LSSM.
460 and DLS 355. Plug the loopback adapter on to the paired LC side of the Test Jumper. The RP 460
button once to put it into the dBm mode.
button once to put it into the dBm mode.
button once to put it into the dBm mode.
460 and DLS 355. Plug the loopback adapter on to the paired LC side of the Test Jumper. The RP 460
Plug the loopback adapter on to the paired LC side of the Test Jumper. The OPM1 should be in the dBm
should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button
should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button
measurement mode. If it is not in the dBm mode, press the dB/dBm button once to put it into the dBm mode.
once to put it into the dBm mode.
once to put it into the dBm mode.
Paired Test Jumper
Setting Reference
Setting Reference
Setting Reference
SETTING REFERENCE
Setting Reference
Setting Reference
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm
The LSSM output power is calibrated to -5dBm. If the OPM1 screen displays between -5.00dBm and -7.00dBm,
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm
and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the dB/dBm button. The OPM1
and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
screen will display 0.00dB, with some minor variation. DO NOT switch the OPM1 back to the dBm mode.
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
RP 460 back to the dBm mode.
RP 460 back to the dBm mode.
RP 460 back to the dBm mode.
RP 460 back to the dBm mode.
RP 460 back to the dBm mode.
Between -5.00 and -7.00dBm
Between -5.00 and -7.00dBm
Between -5.00 and -7.00dBm
Between -5.00 and -7.00dBm
Between -5.00 and -7.00dBm
Between -5.00 and -7.00dBm
Loss Test
Loss Test
Loss Test
LOSS TEST
Loss Test
Loss Test
The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the
The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the
The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the
The paired Test Jumper MUST remain attached to the DLS 355 and RP 460. Do not remove the Test
The paired Test Jumper MUST remain attached to the LSSM and OPM1. Do not remove the Test Jumper from
The paired Test Jumper MUST remain attached to the DLS 355 and RP 460. Do not remove the Test
optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to
optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to
optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to
Jumper from the optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be
the optical link. The connectors on the Test Jumper and the fiber-under-test should be cleaned to appropriate
Jumper from the optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be
appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper
appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper
appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper
cleaned to appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped
standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped LC end of the Test Jumper into
cleaned to appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped
into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the
into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the
into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the
LC end of the Test Jumper into one end of the Fiber-Under-Test using the bulkhead as shown. Plug
one end of the fiber-under-test using the bulkhead as shown. Plug the loopback on to the other end of the
LC end of the Test Jumper into one end of the Fiber-Under-Test using the bulkhead as shown. Plug
Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be
Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be
Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be
the loopback on to the other end of the Fiber-Under-Test. The Insertion Loss of the Fiber-Under-Test
fiber-under-test. The Insertion Loss of the fiber-under-test will be shown on the OPM1 screen.
the loopback on to the other end of the Fiber-Under-Test. The Insertion Loss of the Fiber-Under-Test
will be shown on the RP 460 screen.
shown on the RP 460 screen.
shown on the RP 460 screen.
shown on the RP 460 screen.
will be shown on the RP 460 screen.
Test Jumper
DMT
DMT
DMT
DMT
3330 Earhart Drive, Suite 208
DMT
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Fiber-Under-Test
|
|
Carrollton, TX 75006
Office: 972.556.0916
Loopback Adapter
M-UM038-01 RP 460 Reference and Test
M-UM038-01 RP 460 Reference and Test
M-UM038-01 RP 460 Reference and Test
M-UM038-01 RP 460 Reference and Test
|
Fax: 972.910.8384
M-UM038-01 RP 460 Reference and Test
Reference is set
Reference is set
Reference is set
Reference is set
Reference is set
Reference is set
Loopback
Page 8
OPM1
Page 4
Page 4
Page 4
PAGE 7
Page 8
Advertisement
Table of Contents
