ETI MWPK-1-LB3-CP3-MV-LVD Use And Care Manual

Order # 61509101
Use and Care GUide
slim mOdern Wall PaCk instrUCtiOns
120-277V 50/60Hz 30W/45W/60W 80W/90W/100W 100W/120W/140W
Package contents
Description Quantity
Fixture 1
EVA Foam 1
Default setting is at hightest wattage,
5000cct
30W/45W/60W
nOte: Keep your receipt and these instructions for proof of purchase.
nOte: Do not use an electric generator to test the LED fixture; Please abide by appropriate national, regional and local law and regulations when install this fixture; Do not install the
fixture when raining to lower the risk of electric shock and avoid failure. To avoid possibility of electrical shock or fire, the installation personnel must have professional electric knowledge;
Wear gloves to avoid injury before installation; If any smoke or spark of the wire happened, please turn off the power immediately and notify relevant personnel; This fixture is available in
outdoor usage,but the distance from fixture to ground should be more than 2m. This installation instruction applies to the following products. Although the products vary in appearance, the
installation steps are the same.
WarninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes. Do not use the electric generator to test the LED lamp; This
luminaire must be installed in accordance with your local electrical codes and requirements; Do not install the luminaire in rainy days, to avoid lightning strike and damage to luminaire.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
aPPliCatiOns: Tunnel (except for motor vehicle tunnel), workshop, warehouse, factory, house, building exterior, etc.
InstallatIon I
ON
OFF
1 Turn off the power. 2 Use a screwdriver to remove the screws
on both sides.
Drill mounting holes with an electric drill. Use a screwdriver to remove the plug,
4 5
Attach the EVA cotton pad to bottom.
Mount the cover of the fixture. Fix the fixture with screws.
7 8
Part # mWPk-1-lB3-CP3-mV-lVd Certification # mWPk-1-lB3-CP3-mV-lVd
61509201 mWPk-2-lB3-CP3-mV-lVd
61510101 mWPk-3-lB3-CP3-mV-lVd
80W/90W/100W 100W/120W/140W Fixture
3 Open the fixture, and remove the upper cover of
the fixture.
Lock the bottom shell on the mounting seat with
6
screws, Connect the L, N and G wires to the
power supply.
Make sure the installation is complete before
9
turning on the power switch.
InstallatIon II
mWPk-2-lB3-CP3-mV-lVd
mWPk-3-lB3-CP3-mV-lVd
OFF
Turn off the power.
1
EVA Foam
Lock the bottom shell on the mounting seat
4
with screws.
Fix the fixture with screws.
7
standard Wire: L/live wire: Black\Brown; N/null wire: White\Blue; Ground wire: Green\Yellow-green.
WarninG: During grounding, make sure the ground wire of the driver and fixture housing are connected together with the ground wire of the local power supply.
Wattage anD cct aDjustable
Wattage aDjustable InstructIon
Turn the wattage adjustable knob to a certain wattage gear, the power of the lamp will change to the
corresponding wattage.
Adjustable wattage range 25%-100%.
nOte: Please turn off the power before adjusting the wattage.
color aDjustable InstructIon
The color temperature of the lamp turns to 3000K, 4000K, or 5000K when the switch is set to
corresponding 3K/4K/5K.
nOte: Please turn off the power before adjusting the color temperature.
WarninG: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
nOtiCe: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
ON
the receiver is connected, and consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
OFF
ON
Use a screwdriver to remove the screws
2
on both sides and remove the upper
cover of the fixture.
Connect the L,N and G wires to the power
5
supply.
ON
OFF
Make sure the installation is complete
8
before turning on the power switch.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-etI-sslI (1-855-384-7754) www.etissl.com
Drill mounting holes with an electric drill. Push
3
the expansion rubber plug into the mounting hole
on the wall.
Mount the cover of the fixture.
6
L M H
3K 4K 5K