Wireless Mouse Functions; Connection Example; Functions And Operations - Sharp XG-NV3XU Operation Manual

Wireless Mouse Functions

Connection Example

Personal computer
To mouse terminal
Supplied mouse control cable (for IBM
PS/2, serial and Apple ADB type mouse)

Functions and Operations

POWER ON/OFF
buttons
MOUSE/ADJUSTMENT
switch
• First, connect the units as shown above, and turn the projector power on.
• Second, turn the computer power on.
• Next, slide the MAIN POWER switch on the side of the remote control.
• When using the remote control as a wireless mouse, move the MOUSE/ADJUSTMENT switch to the MOUSE position.
Notes:
• In some situations the wireless mouse may be inoperable if your computer port is not correctly set-up. Please refer to your computer owners
manual for details on setting-up/installing the correct mouse driver.
• Be sure to use the computer control cable when connecting the PC CONTROL terminals.
• Do not connect or remove the mouse control cables and computer control cable to/from your computer while it is on. This may damage your
computer.
• Only one set of connection cables is supplied with your projector. For additional connection cables, contact your nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center.
• Do not connect the mouse input terminal for IBM/Mac and the mouse input terminal for PC98 simultaneously.
MOUSE buttons
By lightly pressing the up/down and right/left arrow buttons located on the front of the remote
control, you can move the mouse cursor on your monitor screen.
Note:
• The amount of pressure applied to the MOUSE button determines the speed the mouse cursor travels. Pressing
lightly on the periphery of the MOUSE button makes the mouse cursor move slowly. Pressing hard makes it move
quickly.
LEFT-CLICK button
RIGHT-CLICK button
LASER POINTER button Press the LASER POINTER button to activate the laser pointer.
"COMPLIES WITH 21 CFR SUBCHAPTER J"
CAUTION
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
TEL : 1-800-BE-SHARP
LASER RADIATION-
DO NOT STARE INTO BEAM
REMOTE CONTROL
MODEL NO. : G1414CESA
WAVE LENGTH : 670nm
DC6V (1.5VX4PCS.)
MAX. OUTPUT : 1mW
MADE IN JAPAN
CLASS II LASER PRODUCT FABRIQUÉ AU JAPON
Rear terminals
IN 1 COMPUTER RGB IN 2 COMPUTER AUDIO
IN 1
AUDIO WIRED
OUT
OUTPUT REMOTE
PC CONTROL
1
L R
IN
1
OFF ON
IN
2
S-VIDEO L R
VIDEO AUDIO 110-120V/
200-240V~
Supplied
computer
control cable
VOL
ON
MUTE
OFF
LASER POINTER button
BLACK LASER/
SCREEN MENU
B
MN
MOUSE buttons
RIGHT-CLICK button
R-CLICK/ENTER
INPUT SELECT
DATA1 DATA2
VIDEO1 VIDEO2
CHECK
MOUSE ADJ.
LIGHT
LCD PROJECTOR
The LEFT-CLICK button on the back of the remote control corresponds to the left button
of the mouse on two-button mouse systems.
The RIGHT-CLICK button on the front of the remote control corresponds to the right
button on two-button mouse systems.
Note: For one-button mouse systems use either the LEFT-CLICK or RIGHT-CLICK button.
When the button is pressed, the light stays on; when the button is released, the light
goes off. However, even when the button is pressed continuously, the light automati-
cally goes off 1 minute after it goes on. To turn it on again press the laser pointer button
one more time.
U.S.A. ONLY
The wireless mouse functions and laser pointer on the
remote control can help you create a more professional
IN 2 presentation.
• By connecting the supplied computer control cable to the
PC CONTROL terminal on your projector and the supplied
2
mouse control cables to the mouse terminal on your
personal computer, you can use the wireless mouse on the
remote control, instead of the mouse equipped with your
personal computer, to operate your personal computer.
The wireless mouse functions will work with personal
computers compatible with IBM PS/2, serial (RS-232C) or
Apple ADB type mouse systems.
The laser pointer on the remote control emits
a laser beam from the laser light window. The
laser emitted is a class II laser; therefore, do
not look into the laser window or shine the
laser beam on yourself or other people. The
two marks to the left are the caution labels for
the laser beam.
Always use the laser pointer at temperatures
between 41°F and 104°F ( 5°C and
40°C).
MAIN POWER switch of remote control
LEFT-CLICK button
Mouse cursor
E-8