Sharp XG-NV5XB Service Manual

Hide thumbs Also See for XG-NV5XB:

Quick reference (2 pages)

Operation manual (54 pages)

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

Table of Contents

Quick Links

Summary of Contents for Sharp XG-NV5XB

Page 1: Table Of Contents
XG-NV5XB SERVICE MANUAL S99O4XG-NV5XB LCD PROJECTOR XG-NV5XB MODEL In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS...
Page 2: Specifications
(TINS-6601CEN1), Sharp Advanced Presentation quick reference (TINS- 6676CEZZ), IrDA driver installation instruction sheet (TCAUZ3046CEZZ) This SHARP projector uses LCD (Liquid Crystal Display) panels. These This unit has some inactive TFTs within acceptable tolerances which very sophisticated panels contain 786,432 pixels (2 RGB) TFTs (Thin may result in illuminated or inactive dots on the picture screen.
Page 3: Important Service Safety Notes
XG-NV5XB IMPORTANT SERVICE SAFETY NOTES Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per WARNING volt., or higher, sensitivity to measure the AC voltage...
Page 4: Note To Service Personnel
XG-NV5XB NOTE TO SERVICE NOTE POUR LE PERSONNEL PERSONNEL D’ENTRETIEN 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5...
Page 5: Lamp Replacement
éviter une exposition des yeux et la peau (Fig. 1). Note: Please obtain a lens cap before servicing a Remarque: Priére de se procurer un capuchon model XG-NV5XB that is received without d'optique acant d'entretien un modéle one. XG-NV5XB qui est livré sans.
Page 6 XG-NV5XB WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS.
Page 7: Location Of Controls
XG-NV5XB Location of Controls Projector 1 POWER indicator 2 POWER buttons (ON/OFF) Front View 3 BLACK SCREEN button 4 INPUT SELECT button 5 FREEZE button 6 KEYSTONE button 7 ADJUSTMENT buttons (∂ /ƒ/ ß / ©) 8 LAMP REPLACEMENT indicator...
Page 8: Operating The Wireless Mouse Remote Control
XG-NV5XB Operating the Wireless Mouse Remote Control “Power” Remote Control 1 MUTE button Front View Side View 2 POWER buttons (ON/OFF) 3 BLACK SCREEN/TOOLS button 4 RIGHT-CLICK/ENTER button 5 INPUT button MUTE 6 FREEZE button 7 KEYSTONE button BLACK SCREEN...
Page 9: Inserting The Batteries
XG-NV5XB Inserting the batteries Press in and downward Insert four AA size batteries Insert the side tabs of on the arrow to remove for the “Power” remote the battery cover into the battery cover. control and two AAA size their slots and press the...
Page 10: Operation Manual
XG-NV5XB When operating the When operating the The “Power” remote control has the following three func- projector controls wireless mouse or tions: using the laser pointer • Operation of projector controls • Operation of wireless mouse • Use of laser pointer MOUSE ADJ.
Page 11 XG-NV5XB Connection Pin Assignments...
Page 12 XG-NV5XB Dimensions Rear View Top View (84) (84) (19) (22) (43) 2 (62) Side View (70) (243.5) (77) (229) (10.5) Front View (25) (11) Bottom View Units: inches (mm)
Page 13: Removing Of Major Parts
XG-NV5XB REMOVING OF MAJOR PARTS 1. Removing the Intake cover and lamp unit 1-1. Detach the Intake cover. 1-2. Loosen the lamp cover screw and draw out the lamp cover in the direction of arrow (toward yourself). 1-3. Remove the two lamp unit lock screws. Detach the lamp unit.
Page 14 XG-NV5XB 2. Removing the top and rear cabinets 2-1. Remove the five rear cabinet lock screws. 2-2. Remove the four terminal board lock screws off the rear cabinet. Unhook and detach the rear cabinet from below. 2-3. Remove the four top cabinet lock screws from below.
Page 15: Removing The Pwb Units
XG-NV5XB 3. Removing the PWB units 3-1. Disconnect the connectors. 3-2. Remove the twelve screws and detach the output Unit top shield. 3-3. Remove the two screws and detach the PC I/F Unit. 3-4. Remove the two screws and the spacer (stud bolt).Lift and detach the Unit assembly.
Page 16 XG-NV5XB 4. Removing the Power/Ballast unit assembly 4-1. Remove the Power/Ballast unit assembly lock screw. 4-2. Remove the two lamp socket holder lock screws and take out the holder. 4-3. Disconnect the connector (BA) from the ballast unit. 4-4. Remove the (FG) lead lock screw.
Page 17 XG-NV5XB 5. Removing the optical mechanism unit 5-1. Remove the six optical mechanism unit lock screws. Lift the unit off the position. 6. Removing the ballast unit and inlet unit 6-1. Disconnect the connector (PA) from the inlet unit. Take out the AC power switch.
Page 18: Resetting The Total Lamp Timer
XG-NV5XB RESETTING THE TOTAL LAMP TIMER When the lamp has been replaced, reset the total lamp timer in the following steps. Resetting procedure 1. While holding down the “ENTER”, “ADJ."” and “ADJ.|” keys on the set at the same time, turn on the main power switch (located side the AC inlet).
Page 19: The Optical Unit Outline
XG-NV5XB THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system. Projection Lens Incident polarizing plate B emergent polarizing plate R AR coating Dichroic coating (R transmission) emergent polarizing plate B B-LCD R-LCD Cross dichroic prism...
Page 20: Convergence And Focus Adjustment
XG-NV5XB CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top panel removed but the power on. Use the remote control to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1.
Page 21 XG-NV5XB 4. With the G-LCD panel's screen center as refernce, adjust the R-LCD and B-LCD panels. 5. Finally tighten up the convergence lock screw "d". Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam's turning and the linear movement are not always uniform.
Page 22 XG-NV5XB Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction Definition Direction of LCD panel X direction LCD right and left Convergence Y direction LCD top and bottom θZ direction Rotation around Z axis LCD turning axis Z direction LCD optical axis θX direction...
Page 23 XG-NV5XB Replacing the LCD panels Detach the top panel and the optical mechanism unit in advance. (1) Remove the four prism holder lock screws. Detach the prism holder from the optical mechanism unit. (2) Remove the LCD panel lock screws (three each for the R-, G- and B-LCD panels). Detach the LCD panels from the prism holder.
Page 24 XG-NV5XB Adjusting the optical axis of the mirrors (M1, M5 and M4/M6) The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking, this adjustment is needed when any of the internal optical components has been replaced.
Page 25: Electrical Adjustment
XG-NV5XB ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. Adjusting point Adjusting conditions Adjusting procedure » Make the following settings: EEPROM 1.
Page 26 XG-NV5XB Adjusting point Adjusting conditions Adjusting procedure » Choose the subject R1-GAIN and adjust the sig- RGB 1 system 1. Make the following choice: black level Group : OUTPUT 1 nal amplitude to 3.6 ±0.1 Vp-p using the control signal amplitude Subject : R1-BLK switches or the remote controller buttons.
Page 27 XG-NV5XB Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller RGB counter- 1. Feed the black-and-red voltage (25%) stripe signal (XGA). buttons, adjust the data in order to minimize the adjustment flicker. 2. Make the following choice: »...
Page 28 XG-NV5XB Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller Video AGC 1. Feed the split color bar sig- nal. buttons, adjust the black-to-white (100%) level Group : VIDEO 1 difference to 1.50 ±0.02 Vp-p.
Page 29 XG-NV5XB Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller PAL color 1. Feed the PAL color bar sig- saturation level nal. buttons, adjust the difference between the 100% Group : VIDEO 1 white portion and the red portion to 0.36 ±0.02 Vp-p.
Page 30: Adjusting The Pc Board
XG-NV5XB Adjusting point Adjusting conditions Adjusting procedure » In the process mode and select L4. Check the pic- 1. Receive the RGB signal. performance ture, brightness, red, blue, clock, phase, horizontal check position, and vertical position. » In the process mode and select OFF. Make sure that...
Page 31: Trouble Shooting Table
XG-NV5XB TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Through-output in trouble Remote control in trouble Go to "Checking the video unit Feed test pattern signal from Through-output circuit in Go to "Checking the remote circuit".
Page 32 XG-NV5XB TROUBLE SHOOTING TABLE (Continued) Checking the video system Is the lamp on? Go to "Lamp fails to light-up". Is specified voltage fed to EA connectors? Check the power circuit and its parts. Are there signal inputs at pins (3) and...
Page 33 XG-NV5XB TROUBLE SHOOTING TABLE (Continued) Checking IC801 (RGB signal output circuit) Are there RGB output waveforms at pins (31), (32) and (33) of IC801? Go to "No color or unusual tone", "No Check the data transfer and other Y signal" or "Out of sync".
Page 34 XG-NV5XB TROUBLE SHOOTING TABLE (Continued) Checking IC806 (3-D noise reduction circuit) and its peripheral circuits Are there signal inputs at pins (40) (Y signal) and (45)(chroma signal) of IC806? Check the buffer circuit of Q814 thru Q816 as well as Q903 thru Q906.
Page 35 XG-NV5XB TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (21) of IC801? Go back to the signal processing block. Is there Y signal output at pin (40) of IC801? Check IC801 and its peripheral circuits.
Page 36 XG-NV5XB TROUBLE SHOOTING TABLE (Continued) Checking the output PWB unit Are there signal inputs at SC1404, SC1405, SC1501 and SC1502? Are voltages applied to EA connectors and SC5502? If there is no signal at EA If there is no signal at SC1404...
Page 37: No Audio Output
XG-NV5XB TROUBLE SHOOTING TABLE (Continued) No audio output Are there audio signal inputs at pin (2) of IC1411? Check the input, the switching circuit of IC3303 and IC3304, and their peripheral circuit,SC3001,SC1502,etc. Are there audio signal outputs at pin (2) of P5508? Check the IC1411 control voltage,and its peripheral circuits.
Page 38 XG-NV5XB TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? Select the right input with remote control. Are the PC, video and LCP cables as specified and properly connected? Use the right cables or reconnect the cables. With the contrast control at maximum, does the image appear? Readjust the video system.
Page 39 XG-NV5XB TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Turn on the power switch. Is discharging sound heard from the lamp? Is the lamp out of socket? Is the ballast cooling fan running? Replace the Reconnect the lamp. lamp into socket.
Page 40 XG-NV5XB TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1 Checking the clock circuit and its peripheral circuits X8001 or its peripheral part faulty. Is X8001 (6MHz) oscillating? Is X8002 (32.768kHz) oscillating? X8002 or its peripheral part faulty. X8003 or its peripheral part faulty.
Page 41 XG-NV5XB TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2 Checking the PLL circuit and its peripheral circuits Are there signals at pins (6) and (22) of IC8015? IC8025 or its peripheral circuit faulty. Is there signal at pin (18) and (19) of IC8015? IC8015 or its peripheral circuit faulty.
Page 42 XG-NV5XB TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3 Checking the S- Checking the VGA's VGA's red video red video circuit and circuit and its its peripheral peripheral circuits circuits Is there signal at pin (13) of IC8004? Is there signal at pin (13) of IC8004? LCP circuitry faulty.
Page 43 XG-NV5XB TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4 Checking the S- Checking the VGA's VGA's green video green video circuit circuit and its and its peripheral peripheral circuits circuits Is there signal at pin (8) of IC8004? Is there signal at pin (8) of IC8004? LCP circuitry faulty.
Page 44 XG-NV5XB TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5 Checking the S- Checking the VGA's VGA's blue video blue video circuit circuit and its and its peripheral peripheral circuits circuits Is there signal at pin (3) of IC8004? Is there signal at pin (3) of IC8004? LCP circuitry faulty.
Page 45 XG-NV5XB TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6 Checking the OSD circuit and its peripheral circuits Display OSD on the screen. Are there signals at pins (56), (58), (71) and (72) of IC8048? IC8029 or its peripheral circuit faulty. Are there signals at pins (34), (35) and (36) of IC8046? IC8048 or its peripheral circuit faulty.
Page 46: Chassis Layout
XG-NV5XB CHASSIS LAYOUT OUTPUT UNIT PC I/F UNIT DUNTK9839DE05 CPCI-0031CE03 INLET UNIT RUNTK0667CEZZ SIGNAL UNIT DUNTK9856DE05 S-OUT/REG UNIT IR-DA UNIT VIDEO UNIT DUNTK9873DE05 DUNTK9858DE05 DUNTK9769DE15 PC TERMINAL UNIT DUNTK9857DE05 BALLAST UNIT POWER UNIT RDENC0290CEZZ CDENC0284CE02...
Page 47: Block Diagram
XG-NV5XB BLOCK DIAGRAM...
Page 48: Overall Wiring Diagram
XG-NV5XB OVERALL WIRING DIAGRAM...
Page 49: Description Of Schematic Diagram
XG-NV5XB DESCRIPTION OF WAVEFORMS SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: 1. Voltages at test points are measured at the supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/ V tester.
Page 50 XG-NV5XB Ë SIGNAL UNIT-1/2...
Page 51 XG-NV5XB Ë IR-DA and SIGNAL UNIT-2/2...
Page 52 XG-NV5XB Ë OUTPUT UNIT-1/5 (Drawing with small PWB attached:...
Page 53 XG-NV5XB Ë OUTPUT UNIT-2/5 (Drawing with small PWB attached:...
Page 54 XG-NV5XB Ë OUTPUT UNIT-3/5 (Drawing with small PWB attached: Small PWB input section...
Page 55 XG-NV5XB Ë OUTPUT UNIT-4/5 (Drawing with small PWB attached:...
Page 56 XG-NV5XB Ë OUTPUT UNIT-5/5 (Drawing with small PWB attached:...
Page 57 XG-NV5XB Ë OUTPUT SMALL PWB...
Page 58 XG-NV5XB Ë OUTPUT UNIT-1/5 (Drawing with small PWB integrated:...
Page 59 XG-NV5XB Ë OUTPUT UNIT-2/5 (Drawing with small PWB integrated:...
Page 60 XG-NV5XB Ë OUTPUT UNIT-3/5 (Drawing with small PWB integrated:...
Page 61 XG-NV5XB Ë OUTPUT UNIT-4/5 (Drawing with small PWB integrated:...
Page 62 XG-NV5XB Ë OUTPUT UNIT-5/5 (Drawing with small PWB integrated:...
Page 63 XG-NV5XB Ë VIDEO UNIT...
Page 64 XG-NV5XB Ë PC TERMINAL UNIT...
Page 65 XG-NV5XB Ë SOUND OUT/REGULATOR UNIT...
Page 66 XG-NV5XB Ë OPERATION KEY UNIT...
Page 67 XG-NV5XB Ë INLET and POWER UNIT-A (INLET) RUNTK0667CEZZ (POWER)PWB-A CDENC0284CE02...
Page 68 XG-NV5XB Ë POWER UNIT-B PWB-B CDENC0284CE02...
Page 69 XG-NV5XB Ë POWER UNIT-C PWB-C CDENC0284CE02...
Page 70 XG-NV5XB Ë PC I/F UNIT-1/8...
Page 71 XG-NV5XB Ë PC I/F UNIT-2/8...
Page 72 XG-NV5XB Ë PC I/F UNIT-3/8...
Page 73 XG-NV5XB Ë PC I/F UNIT-4/8...
Page 74 XG-NV5XB Ë PC I/F UNIT-5/8...
Page 75 XG-NV5XB Ë PC I/F UNIT-6/8...
Page 76 XG-NV5XB Ë PC I/F UNIT-7/8...
Page 77 XG-NV5XB Ë PC I/F UNIT-8/8...
Page 78 XG-NV5XB PRINTED WIRING BOARD ASSEMBLIS Signal Unit (Wiring Side) PC Terminal Unit (Wiring Side) Video Unit (Wiring Side) IR-DA Unit (Wiring Side)
Page 79 XG-NV5XB Signal Unit (Component Side) PC Terminal Unit (Component Side) Video Unit (Component Side) IR-DA Unit (Component Side)
Page 80 XG-NV5XB Output Small PWB (Wiring Side) Output Unit (Wiring Side) (Drawing with small PWB attached:...
Page 81 XG-NV5XB Output Small PWB (Component Side) Output Unit (Component Side) (Drawing with small PWB attached:...
Page 82 XG-NV5XB Output Unit (Wiring Side) (Drawing with small PWB attached:...
Page 83 XG-NV5XB Output Unit (Component Side) (Drawing with small PWB attached:...
Page 84 XG-NV5XB PC I/F Unit (Wiring Side)
Page 85 XG-NV5XB PC I/F Unit (Component Side)
Page 86 XG-NV5XB PWB-A PWB-B PWB-C Power Unit (Wiring Side)
Page 87 XG-NV5XB PWB-A PWB-B PWB-C Power Unit (Component Side)
Page 88 XG-NV5XB Inlet Unit (Wiring Side) Inlet Unit (Component Side)
Page 89 XG-NV5XB Operation Key Unit (Wiring Side) Operation Key Unit (Component Side)
Page 90 XG-NV5XB S-Out/REG Unit (Wiring Side) S-Out/REG Unit (Component Side)
Page 91: Printed Wiring Board Assemblies
For location of SHARP Parts Distributor, TRANSISTORS Please call Toll-Free; 1-800-BE-SHARP Q411 VS2PD601AR/-1 J 2PD601AR Q412 VS2SB1132Q/-1 J 2SB1132Q in CANADA: Contact SHARP Electronics of Canada Limited Q416 VS2PD601AR/-1 J 2PD601AR Phone (416) 890-2100. Q420 VS2SC2411KR-1 J 2SC2411KR Q421 VS2SC2411KR-1...
Page 92 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9856DE05 C861 VCE9PF1CW106M J 10 16V Elect.(N.P) C862 VCCCCY1HH390J J 39p 50V Ceramic SIGNAL UNIT (Continued) C863 VCKYCY1EF104Z J 0.1 25V Ceramic C864 VCE9PF1HW105M J 1.0 50V Elect.(N.P)
Page 93 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9856DE05 R846 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA R848 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA SIGNAL UNIT (Continued) R849 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA...
Page 94 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9856DE05 DUNTK9839DE05 SIGNAL UNIT (Continued) OUTPUT UNIT INTEGRATED CIRCUITS R942 VRS-CY1JF750J J 75 1/16W Metal Oxide AA R943 VRS-CY1JF471J J 470 1/16W Metal Oxide AA IC1004 RH-iX2204CEZZ...
Page 95 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 D5005 VHDMA153///-1 J Diode MA153// D5006 VHDMA153///-1 J Diode MA153// OUTPUT UNIT (Continued) D5007 VHDMA153///-1 J Diode MA153// D5008 VHDMA153///-1 J Diode MA153// Q1302 VS2SA1036KR-1 J 2SA1036KR...
Page 96 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 C1462 VCKYCY1CF104Z J 0.1 16V Ceramic C1463 VCKYCY1CF104Z J 0.1 16V Ceramic OUTPUT UNIT (Continued) C1464 VCKYCY1CF104Z J 0.1 16V Ceramic C1465 VCKYCY1CF104Z J 0.1 16V Ceramic...
Page 97 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 R1062 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA R1065 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA OUTPUT UNIT (Continued) R1066 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA R1067 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA...
Page 98 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 R1237 VRS-CY1JF000J 1/16W Metal Oxide AA R1238 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA OUTPUT UNIT (Continued) R1239 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA R1240 VRS-CY1JF000J...
Page 99 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 R1416 VRS-CY1JF101J J 100 1/16W Metal Oxide AA R1417 VRS-CY1JF101J J 100 1/16W Metal Oxide AA OUTPUT UNIT (Continued) R1418 VRS-CY1JF101J J 100 1/16W Metal Oxide AA...
Page 100 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 R1610 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA R1611 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA OUTPUT UNIT (Continued) R1612 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA R1613 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA...
Page 101 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 R5509 VRS-CB1JF102J J 1.0k 1/16W Metal Oxide AA R5510 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA OUTPUT UNIT (Continued) R5513 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA...
Page 102 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9839DE05 DUNTK9769DE15 OUTPUT UNIT (Continued) VIDEO UNIT INTEGRATED CIRCUITS FB1401 RBLN-0059CEZZ J Ferrite Bead FB1402 RBLN-0059CEZZ J Ferrite Bead IC6001 VHiNJM2245M-1 J NJM2245M FB1501 RBLN-0059CEZZ J Ferrite Bead...
Page 103 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9769DE15 DUNTK9857DE05 VIDEO UNIT (Continued) PC TERMINAL UNIT INTEGRATED CIRCUITS R6011 VRS-CY1JF4R7J J 4.7 1/16W Metal Oxide AA R6047 VRS-CY1JF473J J 47k 1/16W Metal Oxide AA IC3003 VHiTL712CPS-1...
Page 104 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9857DE05 R3103 VRS-CY1JF101J J 100 1/16W Metal Oxide AA R3112 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA PC TERMINAL UNIT (Continued) R3116 VRS-CY1JF101J J 100 1/16W Metal Oxide AA...
Page 105 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9857DE05 DUNTK9873DE05 PC TERMINAL UNIT (Continued) SOUND OUT/REGULATOR UNIT INTEGRATED CIRCUITS FB3007 RBLN-0060TAZZ J Ferrite Bead FB3008 RBLN-0060TAZZ J Ferrite Bead IC1030 RH-iX2204CEZZ J PQ12TZ11 FB3009 RBLN-0060TAZZ...
Page 106 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9873DE05 RUNTK0667CEZZ SOUND OUT/REGULATOR UNIT (Continued) INLET UNIT PACKAGED CIRCUIT R7311 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA R7312 VRS-TX2HF8R2J J 8.2 1/2W Metal Oxide AA å...
Page 107: Power Unit
XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code CDENC0284CE02 C718 95C0C195E4720 J 4700p 50V Ceramic C719 95C0C251E3330 J 0.033 50V Film POWER UNIT C721 95C0C1A9R2210 J 220p Ceramic C722 95C0C1A9R2210 J 220p Ceramic INTEGRATED CIRCUITS...
Page 108 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code CDENC0284CE02 CPCi-0031CE03 POWER UNIT (Continued) PC I/F UNIT INTEGRATED CIRCUITS R756 95C0R3Q0V1020 J 1k 1/8W R757 95C0R3Q0V1020 J 1k 1/8W IC8001 RH-iX3270CEZZ J HD6417709 R758 95C0R390T1810 J 180...
Page 109 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0031CE03 C8025 9DK001-42096 J 0.01 50V Ceramic C8026 9DK001-42096 J 0.01 50V Ceramic PC I/F UNIT (Continued) C8027 9DK001-42096 J 0.01 50V Ceramic C8028 9DK001-42096 J 0.01...
Page 110 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0031CE03 C8179 9DK001-42096 J 0.01 50V Ceramic C8180 9DK001-42096 J 0.01 50V Ceramic PC I/F UNIT (Continued) C8181 9DK001-42096 J 0.01 50V Ceramic C8182 9DK001-42096 J 0.01...
Page 111 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0031CE03 C8354 9DK001-42096 J 0.01 50V Ceramic C8355 9DK001-42101 J 220p 50V Ceramic PC I/F UNIT (Continued) C8359 9DK001-42094 J 0.1 25V Ceramic C8262 9DK001-42096 J 0.01...
Page 112 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0031CE03 R8145 9DK001-50185 J 10k 1/16W Chip 1608 R8147 9DK001-50202 J 51 1/16W Chip 1608 PC I/F UNIT (Continued) R8149 9DK001-50189 J 130k 1/16W Chip 1608 R8150 9DK001-50185...
Page 113 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0031CE03 R8322 9DK001-50205 J 1.8k 1/16W Chip 1608 R8323 9DK001-50150 J 10 1/16W Chip 1608 PC I/F UNIT (Continued) R8324 9DK001-50177 J 1k 1/16W Chip 1608 R8325 9DK001-50150...
Page 114 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code å BQC-XGNV5XB/1 J Lamp/Cage Module Unit CABINET AND MECHANICAL PARTS å 11-1 CLMPF0057DE01 J Lamp/Mirror Ass'y 11-2 CCASZ1032CE01 J Lamp Case Ass'y 11-2-1 PCASZ1032CEKZ J Lamp Case Not Available –...
Page 115: Ë Cabinet And Mechanical Parts
XG-NV5XB CABINET AND MECHANICAL PARTS Ref. No. Part No. Description Code Ref. No. Part No. Description Code...
Page 116 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code OPTICS MECHANISM PARTS CCHSK0075CE21 J Optics Macha. Ass'y LCHSK0081CEFW J Optics Mecha. Base LCHSK0080CEFW J Optics Mecha. Cover CANGK0675CE01 J R/B Convergence Unit, x2 AY LANGK0674CEFW J G Adjusting Plate...
Page 117 XG-NV5XB OPTICS MECHANISM PARTS Ref. No. Part No. Description Code Ref. No. Part No. Description Code...
Page 118 XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code POWER/BALLAST UNIT PARTS Not Available – Power/Ballast Unit Ass'y — 12-1 95C0MPS03180 J Power Case 12-2 95C0MPS03190 J Cover 12-3 95C0M525A0010 J Holder 12-4 95C0MPS03630 J Cover...
Page 119 XG-NV5XB POWER/BALLAST UNIT PARTS Ref. No. Part No. Description Code Ref. No. Part No. Description Code 12-4 12-3 12-16 12-2 12-7 12-9 12-12 PWB-C 12-14 12-14 12-18 12-5 12-6 12-1 PWB-B PWB-A 12-11 12-15 12-13 12-18 12-14 12-10 12-16 12-14...
Page 120: Ë Packing Parts
XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING PARTS SUPPLIED ACCESSORIES (NOT REPLACEMENT ITEM) ACCESSORIES SPAKC5362CEZZ – Packing Case — SPAKP0805CEZZ – Polystyrene Cover — PFiLD0076CEZZ J Extra Air Filter SPAKX2858CEZZ – Buffer Material —...
Page 121: Packing Of The Set
XG-NV5XB Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET CD-ROM Carrying Bag Extra Air Filter Macintosh Adaptor Four AA Size Batteries Guarantee Card Operation Manual Two AAA Size Batteries Wireless R/C Unit...
Page 122 Code Ref. No. Part No. Description Code COPYRIGHT © 1999 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Sharp XG-NV5XB Service Manual

Quick Links

Related Manuals for Sharp XG-NV5XB

Summary of Contents for Sharp XG-NV5XB

Table of Contents