Related Manuals for EasyIO FG32
Summary of Contents for EasyIO FG32
- Page 1 EasyIO FG32 – Installation Guide v2.0 EasyIO FG Series and FG+ Series DDC User Reference...
- Page 2 EasyIO FG32 – Installation Guide v2.0 Document Change Log April 2013 Document created. July 2013 Correct mistakes and typo error. August 2013 Restore Factory settings Sept 2013 Added in wiring diagram August 2015 Updated LED indication table. Jan 2018 Updated UO output specification.
- Page 3 While every effort has been made to assure the accuracy of this document, EasyIO Holdings Pte Ltd is not responsible for damages of any kind, including without limitation consequential damages, arising from the application of the information contained herein.
- Page 4 EasyIO FG32 – Installation Guide v2.0 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
Page 5: Table Of Contents
EasyIO FG32 – Installation Guide v2.0 Table of Contents Introduction ..............................6 Hardware Configurations ..........................7 Power supply Connection ........................... 7 RS485 Connection ............................8 Jumpers Setting ............................9 Wiring diagram ............................10 Digital Output Wiring Connection ......................11 Universal Input Connection ........................12 Universal Output Connection ........................ -
Page 6: Introduction
EasyIO FG32 – Installation Guide v2.0 Introduction EasyIO FG Series is the most powerful Sedona controller in the market. It is equipped with two 32-bit Processors, the first in the Automation industry, with an ARM9 200 MHz Samsung processor (400Mhz for FG+ Series), an ARM M3 Cortex for the I/O management and A-D processing, and also with a Linux 2.6 OS... -
Page 7: Hardware Configurations
Hardware Configurations Power supply Connection Both AC and DC can be used for EasyIO FG Series controller. Refer to electrical specification for the working range. In order to avoid damage on the controller input/output devices and RS485 connection, use individual power supply for each controller. If a single power supply is used, make sure controller power supplies are connected with the same polarity. -
Page 8: Rs485 Connection
EasyIO FG32 – Installation Guide v2.0 RS485 Connection RS485 connection must be terminated at both ends with termination resistor, typically 120 Ohms. It is recommended to use shielded twisted pair wire (STP) for the wiring. The FG series comes with a build in 120 Ohms resistor. To enable this simply set the jumper setting to ON position. -
Page 9: Jumpers Setting
EasyIO FG32 – Installation Guide v2.0 Jumpers Setting Below image shows the jumper setting for Universal Input, Universal Output, Watchdog and also EIA 485 120 Ohm terminations. -
Page 10: Wiring Diagram
EasyIO FG32 – Installation Guide v2.0 Wiring diagram... -
Page 11: Digital Output Wiring Connection
EasyIO FG32 – Installation Guide v2.0 Digital Output Wiring Connection EasyIO FG Series digital output is for general purpose isolated digital output connections (relay output). Pilot Duty rating is as below (Pilot Duty); 24 VAC , 2.0A ... -
Page 12: Universal Input Connection
EasyIO FG32 – Installation Guide v2.0 Universal Input Connection EasyIO FG and FG+ series has non-isolated universal inputs. The universal input supports three type of analog signal i.e. resistance, voltage and current transmitter via hardware jumper and internal register settings:... - Page 13 EasyIO FG32 – Installation Guide v2.0 Universal Input as Pulse Input specifications, Max 20Hzat 50% cycle.
-
Page 14: Universal Output Connection
EasyIO FG32 – Installation Guide v2.0 Universal Output Connection EasyIO FG and FG+ Series has Universal Output connections. Each Universal Output can be configured to drive voltage or current output or digital output via hardware jumper setting and internal register settings. - Page 15 EasyIO FG32 – Installation Guide v2.0 Universal Output Connection as Digital Output Remarks: Universal Output as Digital Output Only DC power source can be use. If AC power source it will damage the controller. Max DC power source is 24VDC.
-
Page 16: Buttons And Indications
Image shows the Reset button, Service button and also TXRX indicators. Image shown is an EasyIO FG-32 unit. Image shows the Status indicator, Error indicator and individual Digital Output indicator Button and LED indications. Image shown is an EasyIO FG-32 unit. -
Page 17: Login Details
TXRX is used to indicate when there are Communication activities in Port 2. TX2 RX2 (Transmitting or Receiving) on the Communication port. Login Details EasyIO FG and FG+ Series details are as below. Sedona Login Username : admin Password : <no password>... -
Page 18: Changing Ip Address
Changing the IP address can only be done through CP T tools. Step 1 Login to the FG32 via Sedona workbench. Locate the object “IP” under the Service folder. Step 2 Click IP object and view properties at the side bar. -
Page 19: Restore Factory Settings
3. Default Sedona apps default login is admin, <no password>. Step 1 Make sure you backup the Sedona apps if you have connection to the EasyIO FG32. Step 2 Cycle power or toggle the reset button. Within 5 seconds press and HOLD down the service button until the Error LED starts to flash approximately 2 Hz. -
Page 20: Technical Support
EasyIO FG32 – Installation Guide v2.0 Technical Support For technical issue, please contact respective region support channel. Worldwide and Asia Pacific Support support@easyio.com Americas Support support@easyio.pro Europe Support support@easyio.eu...